Product Description
The three-phase synchronous motor for TK air compressor complies with relevant IEC international standards. The synchronous motor excitation system uses a static thyristor excitation device. The motor allows direct start at full pressure, and can also be stepped down when the grid capacity does not allow full pressure start. This series of motors has the advantages of compact structure, high efficiency, low noise, low vibration, high reliability, convenient installation and maintenance.
The high-voltage synchronous motor of this series has the protection degree of IP00 and the cooling method is IC01. If other protection levels and cooling method requirements are adopted, it can be negotiated with the user. The rated voltage of this series of motors is 6000 volts, and the allowable voltage of 10000 volts is within ±5%. The rated frequency of the power supply is 50 Hz and the rated power factor is 0.9 (leading).
TK series large three-phase synchronous motor is mainly used to drive reciprocating (piston) air compressors. It is suitable for motors of refrigeration and fertilizer equipment, and can also be used to drive pumps, fans and other general mechanical equipment.
Motor Name: High-voltage synchronous motor for TK air compressor
Power range: 250KW-5000KW
Speed range: 200-1000 r/min
Rated voltage: 380V/3000V/6000V/10000V
Rated frequency: 50HZ/60HZ
Power factor: 0.9
Insulation class: F
Protection level: IP00/IP21/IP23
Installation method: IM7311/IM5710
Working system: S1
Excitation mode: static thyristor, other excitation methods can also be used
Connection: Y
Cooling method: IC01. Other forms of motors can also be produced according to user requirements, such as duct ventilation and air and air cooling.
Altitude: no more than 1000m
Slip rings can be divided into common structure or slip ring positive pressure ventilation.
This type of motor is suitable for use in environments where the ambient air temperature does not exceed 40 ° C and there is no serious dust, the minimum ambient air temperature is -15 ° C, and there is no corrosive and explosive gas in the air (which can also be made into a damp heat or high-altitude motor).
TK series air compressor motors have advanced power factor (which can improve grid power factor), high efficiency, high stability and high overload capability, and have the performance that the speed does not change with the load, especially when the speed is lower than 600r/min. The performance is significantly better than the asynchronous motor of the same speed.
Our company’s motor manufacturing factory adheres to the concept of green, efficient and energy-saving production service, pays attention to the harmonious development of internal and external environment, builds environmentally friendly motor manufacturing enterprises, strictly implements motor standard process, and selects high-quality energy-saving materials to ensure the quality of motor products.
The company insists on providing high-quality motor products and services to users, and has won high praise from many domestic and foreign customers. The company will receive many foreign merchants to visit our factory every year, and establish a good cooperative relationship through on-site inspection of our factory. Our company always welcomes customers to visit our factory.
1. The outer packaging of the products are all standard export-oriented wooden plywood packaging.
2, the product packaging is protected by moisture, water plastic soft packaging
3. For products with special transportation requirements (such as temperature, fragile, variability, and easy to get wet), the packaging protection measures will be strengthened, and the target mark will be printed on the package.
4. There are obvious signs and symbols on the packing box that must be paid attention to during transportation and storage (such as position, moisture, rain, shockproof, lifting position, etc.).
/* January 22, 2571 19:08:37 */!function(){function s(e,r){var a,o={};try{e&&e.split(“,”).forEach(function(e,t){e&&(a=e.match(/(.*?):(.*)$/))&&1
| Application: | Industrial |
|---|---|
| Operating Speed: | Low Speed |
| Operation Mode: | Electric Motor |
| Magnetic Structure: | Electromagnetic Deceleration |
| Function: | Driving |
| Structure: | Rotating Pole Type (Armature Fixed) |
| Customization: |
Available
|
|
|---|
Can electric motors be adapted for use in both residential and industrial settings?
Yes, electric motors can be adapted for use in both residential and industrial settings. Their versatility, efficiency, and wide range of power options make them suitable for various applications in both environments. Here’s a detailed explanation of how electric motors can be adapted for use in residential and industrial settings:
- Residential Applications: Electric motors find numerous applications in residential settings, where their compact size, quiet operation, and energy efficiency are highly valued. Some common residential uses of electric motors include:
- Home Appliances: Electric motors power a wide range of home appliances such as refrigerators, washing machines, dishwashers, vacuum cleaners, fans, and air conditioners. These motors are designed to provide efficient and reliable operation while minimizing noise and energy consumption.
- Garage Door Openers: Electric motors are commonly used in residential garage door openers, providing convenient and automated access to the garage.
- HVAC Systems: Electric motors drive the fans and compressors in heating, ventilation, and air conditioning (HVAC) systems, contributing to efficient climate control and indoor comfort.
- Pool Pumps: Electric motors power pool pumps, circulating water and maintaining water quality in residential swimming pools.
- Power Tools: Electric motors are integral components of various power tools used in residential settings, including drills, saws, and trimmers.
- Industrial Applications: Electric motors are extensively used in industrial settings due to their reliability, controllability, and adaptability to various industrial processes. Some common industrial applications of electric motors include:
- Manufacturing Machinery: Electric motors drive a wide range of manufacturing machinery, including conveyor systems, pumps, compressors, mixers, and agitators. These motors are capable of providing precise speed and torque control, enhancing productivity and process efficiency.
- Industrial Fans and Blowers: Electric motors power fans and blowers for ventilation, cooling, and air circulation in industrial facilities, contributing to a comfortable and safe working environment.
- Machine Tools: Electric motors drive machine tools such as lathes, milling machines, and grinders, enabling precision machining operations in industrial manufacturing processes.
- Material Handling Equipment: Electric motors are widely used in material handling equipment such as forklifts, conveyor systems, and hoists, facilitating efficient movement and transportation of goods within industrial facilities.
- Pumps and Compressors: Electric motors power pumps and compressors in industrial applications, such as water supply systems, HVAC systems, and pneumatic systems.
- Adaptability and Customization: Electric motors can be adapted and customized to meet specific requirements in both residential and industrial settings. They are available in a wide range of sizes, power ratings, and configurations to accommodate diverse applications. Motors can be designed for different voltages, frequencies, and environmental conditions, allowing for seamless integration into various systems and equipment. Additionally, advancements in motor control technologies, such as variable frequency drives (VFDs), enable precise speed and torque control, making electric motors highly versatile and adaptable to different operational needs.
- Energy Efficiency and Environmental Benefits: The use of electric motors in both residential and industrial settings offers significant energy efficiency advantages. Electric motors have higher efficiency compared to other types of motors, resulting in reduced energy consumption and operational costs. Furthermore, electric motors produce zero direct emissions at the point of use, contributing to a cleaner and more sustainable environment. In residential settings, energy-efficient electric motors in appliances and HVAC systems help homeowners reduce their energy bills and minimize their carbon footprint. In industrial applications, the adoption of electric motors supports energy conservation initiatives and aligns with sustainability goals.
In summary, electric motors are adaptable for use in both residential and industrial settings. Their compact size, energy efficiency, controllability, and versatility make them suitable for a wide range of applications, from home appliances and garage door openers to manufacturing machinery and material handling equipment. The use of electric motors brings benefits such as improved energy efficiency, reduced emissions, quieter operation, and enhanced control, contributing to the efficiency and sustainability of residential and industrial operations.
Can electric motors be used in renewable energy systems like wind turbines?
Yes, electric motors can be used in renewable energy systems like wind turbines. In fact, electric motors play a crucial role in converting the kinetic energy of the wind into electrical energy in wind turbines. Here’s a detailed explanation of how electric motors are utilized in wind turbines and their role in renewable energy systems:
Wind turbines are designed to capture the energy from the wind and convert it into electrical power. Electric motors are used in wind turbines to drive the rotation of the turbine blades and generate electricity through the following process:
- Wind Capture: The wind turbine blades are designed to efficiently capture the kinetic energy of the wind. As the wind blows, it causes the blades to rotate.
- Blade Rotation: The rotational motion of the turbine blades is achieved through electric motors known as pitch motors. Pitch motors adjust the angle or pitch of the blades to optimize their orientation relative to the wind direction. The electric motors drive the mechanical mechanism that rotates the blades, allowing them to capture the maximum energy from the wind.
- Power Generation: The rotation of the wind turbine blades drives the main shaft of the turbine, which is connected to an electric generator. The generator consists of another electric motor known as the generator motor or generator rotor. The rotational motion of the generator rotor within a magnetic field induces an electrical current in the generator’s stator windings, producing electricity.
- Power Conversion and Distribution: The electricity generated by the wind turbine’s generator motor is typically in the form of alternating current (AC). To make it compatible with the electrical grid or local power system, the AC power is converted to the appropriate voltage and frequency using power electronics such as inverters. These power electronics may also incorporate electric motors for various conversion and control functions.
- Integration with Renewable Energy Systems: Wind turbines, equipped with electric motors, are integrated into renewable energy systems to contribute to the generation of clean and sustainable power. Multiple wind turbines can be connected together to form wind farms, which collectively generate significant amounts of electricity. The electricity produced by wind turbines can be fed into the electrical grid, used to power local communities, or stored in energy storage systems for later use.
Electric motors in wind turbines enable the efficient conversion of wind energy into electrical energy, making wind power a viable and renewable energy source. The advancements in motor and generator technologies, along with control systems and power electronics, have enhanced the performance, reliability, and overall efficiency of wind turbines. Additionally, electric motors allow for precise control and adjustment of the turbine blades, optimizing the energy capture and minimizing the impact of varying wind conditions.
Overall, the use of electric motors in wind turbines is instrumental in harnessing the power of wind and contributing to the generation of clean and sustainable energy in renewable energy systems.
How do electric motors generate motion and mechanical work?
Electric motors generate motion and mechanical work through the interaction of magnetic fields and the conversion of electrical energy into mechanical energy. Here’s a detailed explanation of how electric motors accomplish this:
- Magnetic Fields: Electric motors consist of a stationary part called the stator and a rotating part called the rotor. The stator contains coils of wire that are supplied with an electric current, creating a magnetic field around them. The rotor, on the other hand, typically has magnets or electromagnets that produce their own magnetic fields.
- Magnetic Field Interaction: When an electric current flows through the coils in the stator, it generates a magnetic field. The interaction between the magnetic fields of the stator and the rotor creates a rotational force, also known as torque. This torque causes the rotor to start rotating.
- Electromagnetic Induction: In certain types of electric motors, such as induction motors, electromagnetic induction plays a significant role. When alternating current (AC) is supplied to the stator, it creates a changing magnetic field. This changing magnetic field induces voltage in the rotor, which leads to the flow of current in the rotor. The current in the rotor produces its own magnetic field, and the interaction between the stator’s magnetic field and the rotor’s magnetic field results in rotation.
- Commutation: In motors that use direct current (DC), such as brushed DC motors, commutation is employed. Commutation is the process of reversing the direction of current in the rotor’s electromagnets as the rotor rotates. This is done using a component called a commutator, which ensures that the magnetic fields of the rotor and the stator are always properly aligned. By periodically reversing the current, the commutator allows for continuous rotation.
- Conversion of Electrical Energy to Mechanical Energy: As the rotor rotates, the mechanical energy is produced. The rotational motion of the rotor is transferred to the motor’s output shaft, which is connected to the load or the device that needs to be driven. The mechanical work is performed as the output shaft drives the load, such as spinning a fan blade, rotating a conveyor belt, or powering a machine.
In summary, electric motors generate motion and mechanical work by utilizing the interaction of magnetic fields and the conversion of electrical energy into mechanical energy. The electric current flowing through the stator’s coils creates a magnetic field that interacts with the magnetic field of the rotor, producing torque and initiating rotation. In some motors, electromagnetic induction is employed, where a changing magnetic field induces voltage and current in the rotor, leading to rotation. Commutation, in certain motor types, ensures continuous rotation by reversing the current in the rotor’s electromagnets. The resulting rotational motion is then transferred to the motor’s output shaft, enabling the motor to perform mechanical work by driving the load.
editor by CX 2024-05-07
China Hot selling 220V 10W Shaded Pole Small Electric Refrigerator Motor Compressor with Best Sales
Product Description
Product Description
The YZF26 series motor adopts the end cover with 26mm mounting bracket screw spacing , which has the advantages of safety , reliability , low noise , small vibration and long life.
This series of motor is suitable for refrigerating equipment such as freezer , refrigerator, wine cabinet , fresh – keeping cabinet , condenser, evaporator, display chiller, radiator , etc.
The lead wire specification, size ” L ” and terminal of motor can be customized.
Installation Instructions
Operating Mode:S1 Insulation Grade: Class E
Protection Class: IP41 Environmental Temperature:-30ºC~+50ºC
Drawing
Product Parameters
| TYPE | YZF3-13T | YZF5-13T | YZF10-20T | YZF16-25T | YZF20-30T | YZF25-40T | YZF34-45T | ||||||
| VOLTAGE V | 220-240 | 220-240 | 110-120 | 220-240 | 110/120 | 220-240 | 110-120 | 220-240 | 110-120 | 220-240 | 110-120 | 220-240 | 110-120 |
| FREQUENCY Hz | 50/60 | 50/60 | 60 | 50/60 | 60 | 50/60 | 60 | 50/60 | 60 | 50/60 | 60 | 50/60 | 60 |
| INPUT POWER W | 25 | 35 | 35 | 40 | 40 | 60 | 60 | 75 | 75 | 90 | 90 | 110 | 110% |
| OUTPUT POWER W | 3 | 5 | 5 | 10 | 10 | 16 | 16 | 20 | 20 | 25 | 25 | 34 | 34, |
| RATED CURRENT A | 0.16 | 0.21 | 0.45 | 0.25 | 6 | 0.37 | 0.7 | 0.50 | 1.10 | 0.65 | 1.35 | 0.75 | 1.50 |
| RATED SPEED r/min | 1300 | 1300 | 1450 | 1300 | 1450 | 1300 | 1450 | 1300 | 1450 | 1300 | 1450 | 1300 | 1450 |
| AIR VOLUME m3/h | 210 | 455 | 510 | 645 | 790 | 780 | 900 | 1000 | 1050 | 1030 | 1100 | 1080 | 1210 |
| A mm | 13 | 13 | 19 | 25 | 30 | 40 | 45 | ||||||
| B mm | 15 | 15 | 16 | 16 | 16 | 16 | 16 | ||||||
| C mm | 45 | 45 | 46 | 46 | 46 | 46 | 46 | ||||||
| D mm | 78 | 78 | 85 | 92 | 97 | 06 | 114 | ||||||
| FAN BLADE mm | Φ170 | Φ200 | Φ230 | Φ250 | Φ254 | Φ300 | Φ300 | ||||||
| NET WEIGHT kg | 0.8 | 0.8 | . | 1.3 | 1.5 | 1.8 | 2.1 | ||||||
| QTY/CTN pcs | 24 | 24 | 24 | 12 | 12 | 12 | 12 | ||||||
| CERTIFICATION | CE CCC | CE CCC | CE CCC | CE CCC | CE CCC | CE CCC | CE CCC | ||||||
/* January 22, 2571 19:08:37 */!function(){function s(e,r){var a,o={};try{e&&e.split(“,”).forEach(function(e,t){e&&(a=e.match(/(.*?):(.*)$/))&&1
| Application: | Refrigeration Equipment |
|---|---|
| Operating Speed: | Constant Speed |
| Power Source: | AC Motor |
| Function: | Refrigeration |
| Casing Protection: | Protection Type |
| Number of Poles: | 4 |
| Samples: |
US$ 2.2/Piece
1 Piece(Min.Order) | |
|---|
| Customization: |
Available
|
|
|---|
Can you provide examples of machinery or equipment that rely on electric motors?
Electric motors are extensively used in various machinery and equipment across different industries. They play a crucial role in converting electrical energy into mechanical energy to power a wide range of applications. Here are some examples of machinery and equipment that heavily rely on electric motors:
- Industrial Machinery: Electric motors are found in numerous industrial machinery and equipment, such as pumps, compressors, fans, conveyors, agitators, mixers, and machine tools. These motors provide the necessary power for moving fluids, gases, and materials, as well as driving mechanical processes in manufacturing, mining, construction, and other industrial applications.
- Electric Vehicles: Electric motors are the primary propulsion system in electric vehicles (EVs) and hybrid electric vehicles (HEVs). They provide the power needed to drive the wheels and propel the vehicle. Electric motors in EVs and HEVs offer high efficiency, instant torque, and regenerative braking capabilities, contributing to the advancement of sustainable transportation.
- Household Appliances: Many household appliances rely on electric motors for their operation. Examples include refrigerators, air conditioners, washing machines, dishwashers, vacuum cleaners, blenders, and electric fans. Electric motors enable the movement, cooling, or mechanical functions in these appliances, enhancing convenience and efficiency in daily household tasks.
- HVAC Systems: Heating, ventilation, and air conditioning (HVAC) systems utilize electric motors for various functions. Motors power the fans in air handling units, circulate air through ducts, and drive compressors in air conditioning and refrigeration systems. Electric motors in HVAC systems contribute to efficient temperature control and air circulation in residential, commercial, and industrial buildings.
- Medical Equipment: Electric motors are essential components in a wide array of medical equipment. Examples include MRI machines, X-ray machines, CT scanners, surgical robots, dental drills, infusion pumps, and patient lifts. These motors enable precise movements, imaging capabilities, and mechanical functions in medical devices, supporting diagnostics, treatment, and patient care.
- Power Tools: Electric motors are commonly used in power tools such as drills, saws, grinders, sanders, and routers. They provide the rotational force and power required for cutting, shaping, drilling, and other tasks. Electric motors in power tools offer portability, ease of use, and consistent performance for both professional and DIY applications.
- Aircraft Systems: Electric motors are increasingly utilized in aircraft systems. They power various components, including landing gear actuation systems, fuel pumps, hydraulic systems, and cabin air circulation systems. Electric motors in aircraft contribute to weight reduction, energy efficiency, and improved reliability compared to traditional hydraulic or pneumatic systems.
These examples represent just a fraction of the machinery and equipment that rely on electric motors. From industrial applications to household appliances and transportation systems, electric motors are integral to modern technology, providing efficient and reliable mechanical power for a wide range of purposes.
Are there any emerging trends in electric motor technology, such as smart features?
Yes, there are several emerging trends in electric motor technology, including the integration of smart features. These trends aim to improve motor performance, efficiency, and functionality, while also enabling connectivity and advanced control capabilities. Here’s a detailed explanation of some of the emerging trends in electric motor technology:
- Internet of Things (IoT) Integration: Electric motors are becoming increasingly connected as part of the broader IoT ecosystem. IoT integration allows motors to communicate, share data, and be remotely monitored and controlled. By embedding sensors, communication modules, and data analytics capabilities, motors can provide real-time performance data, predictive maintenance insights, and energy consumption information. This connectivity enables proactive maintenance, optimized performance, and enhanced energy efficiency.
- Condition Monitoring and Predictive Maintenance: Smart electric motors are equipped with sensors that monitor various parameters such as temperature, vibration, and current. This data is analyzed in real-time to detect anomalies and potential faults. By implementing predictive maintenance algorithms, motor failures can be anticipated, enabling maintenance activities to be scheduled proactively. This trend reduces unplanned downtime, improves reliability, and optimizes maintenance costs.
- Advanced Motor Control and Optimization: Emerging electric motor technologies focus on advanced motor control techniques and optimization algorithms. These advancements allow for precise control of motor performance, adapting to changing load conditions, and optimizing energy efficiency. Additionally, sophisticated control algorithms enable motor systems to operate in coordination with other equipment, such as variable speed drives, power electronics, and energy storage systems, resulting in improved overall system efficiency.
- Energy Harvesting and Regenerative Features: Electric motors can harness energy through regenerative braking and energy harvesting techniques. Regenerative braking allows motors to recover and convert kinetic energy into electrical energy, which can be fed back into the system or stored for later use. Energy harvesting technologies, such as piezoelectric or electromagnetic systems, can capture ambient energy and convert it into usable electrical energy. These features enhance energy efficiency and reduce overall power consumption.
- Integration with Artificial Intelligence (AI) and Machine Learning (ML): The integration of electric motors with AI and ML technologies enables advanced motor control, optimization, and decision-making capabilities. AI and ML algorithms analyze motor performance data, identify patterns, and make real-time adjustments to optimize efficiency and performance. The combination of AI/ML with electric motors opens up possibilities for autonomous motor control, adaptive energy management, and intelligent fault detection.
- Miniaturization and Lightweight Design: Emerging trends in electric motor technology focus on miniaturization and lightweight design without compromising performance. This trend is particularly relevant for portable devices, electric vehicles, and aerospace applications. Advancements in materials, manufacturing processes, and motor design allow for smaller, lighter, and more powerful motors, enabling greater mobility, improved efficiency, and increased power density.
The integration of smart features in electric motor technology is driving advancements in connectivity, data analytics, predictive maintenance, advanced control, energy harvesting, AI/ML integration, and miniaturization. These trends are revolutionizing the capabilities and functionality of electric motors, making them more intelligent, efficient, and adaptable to various applications. As technology continues to evolve, electric motors are expected to play a crucial role in the ongoing transition towards smart and sustainable industries.
What are the different types of electric motors available?
There are various types of electric motors available, each designed for specific applications and operating principles. These motors differ in their construction, power sources, and performance characteristics. Here is an overview of some common types of electric motors:
- DC Motors: DC (Direct Current) motors are widely used and come in different configurations. The most common types include brushed DC motors and brushless DC motors. Brushed DC motors use brushes and a commutator to switch the direction of current in the rotor, while brushless DC motors use electronic commutation. DC motors offer good speed control and torque characteristics, making them suitable for applications like robotics, electric vehicles, and small appliances.
- AC Motors: AC (Alternating Current) motors are classified into several types, including induction motors, synchronous motors, and universal motors. Induction motors are popular for their simplicity and reliability. They operate based on electromagnetic induction and are commonly used in industrial and residential applications. Synchronous motors operate at a constant speed and are often used in applications that require precise control, such as industrial machinery and synchronous clocks. Universal motors are designed to operate on both AC and DC power sources and are commonly found in household appliances like vacuum cleaners and power tools.
- Stepper Motors: Stepper motors are designed to move in discrete steps or increments, making them suitable for applications that require precise positioning. They are often used in robotics, 3D printers, CNC machines, and other automated systems. Stepper motors are available in various configurations, including permanent magnet stepper motors, variable reluctance stepper motors, and hybrid stepper motors.
- Servo Motors: Servo motors are a type of motor that combines a DC motor with a feedback control mechanism. They are known for their precise control over position, velocity, and acceleration. Servo motors are commonly used in robotics, industrial automation, and applications that require accurate motion control, such as robotic arms, RC vehicles, and camera gimbals.
- Linear Motors: Linear motors are designed to produce linear motion instead of rotational motion. They operate on similar principles as rotary motors but with a different mechanical arrangement. Linear motors find applications in high-speed transportation systems, cutting machines, and other systems that require linear motion without the need for mechanical conversion from rotary to linear motion.
- Haptic Motors: Haptic motors, also known as vibration motors, are small motors used to create tactile feedback or vibrations in electronic devices. They are commonly found in smartphones, game controllers, wearable devices, and other gadgets that require haptic feedback to enhance the user experience.
These are just a few examples of the different types of electric motors available. Each type has its own advantages, limitations, and specific applications. The selection of an electric motor depends on factors such as the required torque, speed, control, efficiency, and the specific needs of the application at hand.
editor by CX 2024-04-08
China Good quality Yy My Ml Yc Mc Ys Ms Y2 Ie2 Ye2 Capacitor Start Run B14 B5 Single Three Phase Induction AC Electric Electrical Motor for Fans Blowers Pumps Compressor Cleaners manufacturer
Product Description
YY series single phase capacitor run asynchronous motors,are suitable for fans, blowers, and various equipments requiring light load starting.This series motors with high power factor and efficiency, small size, light weight, good performance, low noise, and convenient maintenance
| Power: | 0.55kw-2.2kw | Voltage: | 220/230V( can can done as your need) |
| Frequency: | 50/60hz | Enamelled Wire: | Copper Wire (Can Done Aluminum wire as Your Need) |
| Insulation Class: | F | Mounting Way: | B3/B5/B14/B34/B35 |
| Protection Grade: | IP54 IP44 | motor body : | cast iron/cast aluminum |
.
1. Are you a manufacturer or trading company?
We are a professional manufacturer of single phase motor,three phase electric motor and pump
2. Where is your factory located?
Our factory is in HangZhou,HangZhou,ZHangZhoug,China. it is very near from HangZhou city,HangZhou city,ZheJiang city.
3. How do you confirm your quality?
A. Rich experience on weakness may appear on every components and products;
B. 100% checking before order and bulk sample reserved in warehouse for after-sale service.
4. Is it acceptable to use self-label brand?
Yes, we provide OEM products, also welcome ODM OTM orders.
5. What is your payment terms?
T/T and L/C. Normally T/T 30% deposit, 70% balance should be paid against the B/L copy.
Better payment terms Available for regular esteemed customers.
6. What is your company’s production capacity every year?
We have over 200,000 pcs production capacity every year.
7. Is sample available for my reference before final order?
Yes, we support trial sample order(1-100pcs) for you. Please contact with our sevice staff.
If you have any other questions,welcome to contact us.
| Application: | Industrial |
|---|---|
| Speed: | Variable Speed |
| Number of Stator: | Single-Phase |
| Samples: |
US$ 60/Piece
1 Piece(Min.Order) | Order Sample 1.1kw
|
|---|
| Customization: |
Available
|
|
|---|
.shipping-cost-tm .tm-status-off{background: none;padding:0;color: #1470cc}
|
Shipping Cost:
Estimated freight per unit. |
about shipping cost and estimated delivery time. |
|---|
| Payment Method: |
|
|---|---|
|
Initial Payment Full Payment |
| Currency: | US$ |
|---|
| Return&refunds: | You can apply for a refund up to 30 days after receipt of the products. |
|---|
How does an electric motor ensure efficient energy conversion?
An electric motor ensures efficient energy conversion by employing various design features and principles that minimize energy losses and maximize the conversion of electrical energy into mechanical energy. Here’s a detailed explanation of how electric motors achieve efficient energy conversion:
- Efficient Motor Design: Electric motors are designed with careful consideration given to their construction and materials. High-quality magnetic materials, such as laminated iron cores and permanent magnets, are used to reduce magnetic losses and maximize magnetic field strength. Additionally, the motor’s windings are designed with low-resistance conductors to minimize electrical losses. By optimizing the motor’s design, manufacturers can improve its overall efficiency.
- Reducing Friction and Mechanical Losses: Electric motors are designed to minimize friction and mechanical losses. This is achieved through the use of high-quality bearings and lubrication systems that reduce friction between moving parts. By reducing friction, the motor can operate more efficiently, translating more of the input energy into useful mechanical work rather than dissipating it as heat.
- Efficient Control and Power Electronics: Electric motors employ advanced control techniques and power electronics to enhance energy conversion efficiency. Variable frequency drives (VFDs) are commonly used to control motor speed and torque, allowing the motor to operate at optimal efficiency levels under varying load conditions. Power electronics devices, such as insulated gate bipolar transistors (IGBTs) and MOSFETs, minimize switching losses and optimize power flow within the motor.
- Regenerative Braking and Energy Recovery: Some electric motors, particularly those used in hybrid electric vehicles (HEVs) and electric trains, incorporate regenerative braking systems. These systems convert the kinetic energy of the moving vehicle back into electrical energy, which can be stored and reused. By capturing and reusing energy that would otherwise be wasted as heat during braking, regenerative braking significantly improves overall energy efficiency.
- Efficient Cooling and Thermal Management: Electric motors generate heat during operation, and excessive heat can lead to energy losses and reduced efficiency. To mitigate this, motors are designed with efficient cooling systems such as fans, heat sinks, or liquid cooling methods. Proper thermal management ensures that the motor operates within the optimal temperature range, reducing losses and improving overall efficiency.
- High-Efficiency Standards and Regulations: Governments and organizations have established energy efficiency standards and regulations for electric motors. These standards encourage manufacturers to produce motors with higher efficiency ratings. Compliance with these standards ensures that motors meet certain efficiency criteria, resulting in improved energy conversion and reduced energy consumption.
By incorporating these design features, control techniques, and efficiency measures, electric motors achieve efficient energy conversion. They minimize energy losses due to factors such as resistance, friction, and heat dissipation, ensuring that a significant portion of the input electrical energy is converted into useful mechanical work. The continuous advancements in motor design, materials, and control technologies further contribute to improving the overall energy efficiency of electric motors.
How do electric motors impact the overall productivity of manufacturing processes?
Electric motors have a significant impact on the overall productivity of manufacturing processes. Their versatility, reliability, and efficiency make them essential components in a wide range of industrial applications. Here’s a detailed explanation of how electric motors contribute to enhancing productivity in manufacturing:
- Mechanization and Automation: Electric motors serve as the primary power source for a vast array of industrial machinery and equipment. By providing mechanical power, electric motors enable mechanization and automation of manufacturing processes. They drive conveyor belts, pumps, compressors, robots, and other machinery, allowing for efficient material handling, assembly, and production operations. The use of electric motors in mechanized and automated systems reduces manual labor, accelerates production rates, and improves overall productivity.
- Precise Control and Repeatable Movements: Electric motors offer precise control over speed, position, and torque, enabling accurate and repeatable movements in manufacturing processes. This precision is crucial for tasks that require consistent and controlled operations, such as precision cutting, drilling, machining, and assembly. Electric motors allow for fine adjustments and control, ensuring that manufacturing operations are performed with high levels of accuracy and repeatability, which ultimately enhances productivity and product quality.
- High Speed and Acceleration: Electric motors are capable of achieving high rotational speeds and rapid acceleration, enabling fast-paced manufacturing processes. Motors with high-speed capabilities are utilized in applications that require quick operations, such as high-speed machining, packaging, and sorting. The ability of electric motors to rapidly accelerate and decelerate facilitates efficient cycle times and overall process throughput, contributing to increased productivity.
- Reliability and Durability: Electric motors are known for their reliability and durability, making them well-suited for demanding manufacturing environments. With proper maintenance, electric motors can operate continuously for extended periods, minimizing downtime due to motor failures. The reliability of electric motors ensures consistent and uninterrupted production, optimizing manufacturing productivity and reducing costly disruptions.
- Energy Efficiency: Electric motors have witnessed significant advancements in energy efficiency, leading to reduced energy consumption in manufacturing processes. Energy-efficient motors convert a higher percentage of electrical input power into useful mechanical output power, resulting in lower energy costs. By utilizing energy-efficient electric motors, manufacturers can achieve cost savings and improve the overall sustainability of their operations. Additionally, energy-efficient motors generate less heat, reducing the need for cooling and improving the overall efficiency of auxiliary systems.
- Integration with Control Systems: Electric motors can be seamlessly integrated with sophisticated control systems and automation technologies. This integration allows for centralized control, monitoring, and optimization of manufacturing processes. Control systems can regulate motor speed, torque, and performance based on real-time data, enabling adaptive and efficient operations. The integration of electric motors with control systems enhances the overall productivity by optimizing process parameters, minimizing errors, and facilitating seamless coordination between different stages of manufacturing.
Electric motors significantly impact the overall productivity of manufacturing processes by enabling mechanization, automation, precise control, high-speed operations, reliability, energy efficiency, and integration with advanced control systems. Their versatility and performance characteristics make them indispensable in a wide range of industries, including automotive, electronics, aerospace, food processing, and more. By harnessing the power of electric motors, manufacturers can streamline operations, improve product quality, increase throughput, and ultimately enhance productivity in their manufacturing processes.
What industries and applications commonly use electric motors?
Electric motors are widely utilized in various industries and applications due to their versatility, efficiency, and controllability. Here’s a detailed overview of the industries and applications where electric motors are commonly employed:
- Industrial Manufacturing: Electric motors are extensively used in industrial manufacturing processes. They power machinery and equipment such as conveyor systems, pumps, compressors, fans, mixers, robots, and assembly line equipment. Electric motors provide efficient and precise control over motion, making them essential for mass production and automation.
- Transportation: Electric motors play a crucial role in the transportation sector. They are used in electric vehicles (EVs) and hybrid electric vehicles (HEVs) to drive the wheels, providing propulsion. Electric motors offer benefits such as high torque at low speeds, regenerative braking, and improved energy efficiency. They are also employed in trains, trams, ships, and aircraft for various propulsion and auxiliary systems.
- HVAC Systems: Heating, ventilation, and air conditioning (HVAC) systems utilize electric motors for air circulation, fans, blowers, and pumps. Electric motors help in maintaining comfortable indoor environments and ensure efficient cooling, heating, and ventilation in residential, commercial, and industrial buildings.
- Appliances and Household Devices: Electric motors are found in numerous household appliances and devices. They power refrigerators, washing machines, dryers, dishwashers, vacuum cleaners, blenders, food processors, air conditioners, ceiling fans, and many other appliances. Electric motors enable the necessary mechanical actions for these devices to function effectively.
- Renewable Energy: Electric motors are integral components of renewable energy systems. They are used in wind turbines to convert wind energy into electrical energy. Electric motors are also employed in solar tracking systems to orient solar panels towards the sun for optimal energy capture. Additionally, electric motors are utilized in hydroelectric power plants for controlling water flow and generating electricity.
- Medical Equipment: Electric motors are crucial in various medical devices and equipment. They power surgical tools, pumps for drug delivery and fluid management, diagnostic equipment, dental drills, patient lifts, wheelchair propulsion, and many other medical devices. Electric motors provide the necessary precision, control, and reliability required in healthcare settings.
- Robotics and Automation: Electric motors are extensively used in robotics and automation applications. They drive the joints and actuators of robots, enabling precise and controlled movement. Electric motors are also employed in automated systems for material handling, assembly, packaging, and quality control in industries such as automotive manufacturing, electronics, and logistics.
- Aerospace and Defense: Electric motors have significant applications in the aerospace and defense sectors. They are used in aircraft for propulsion, control surfaces, landing gear, and auxiliary systems. Electric motors are also employed in military equipment, drones, satellites, guided missiles, and underwater vehicles.
These are just a few examples of the industries and applications where electric motors are commonly used. Electric motors provide a reliable, efficient, and controllable means of converting electrical energy into mechanical energy, making them essential components in numerous technologies and systems across various sectors.
editor by CX 2023-12-15
China Good quality CE ISO9001 50Hz 60Hz Yb2 Yb3 Ybx3 Ybx4 Yd Yej Yvp Yvf Three Phase Explosion Proof Flame Proof Electric Motor for Blower Compressor Pump LPG (0.75KW-315KW) vacuum pump diy
Product Description
We,GOGOGO Mechanical&Electrical Co.,Ltd specialize in high quality energy-efficient electric motors.
Our main range is 3 phase general use motors and explosion proof motors.0.75kw-315kw 2pole 4pole 6pole 8 pole
YB2 series explosion-proof three-phase asynchronous motor is a new kind of product developed on the basis of YB and YB2 series motors adopts the latest technology in the world such as electromagnetic structure, craft and materials etc. It has the advantages of high efficiency, energy saving, large temperature rise margin, long life, good performance, low noise, advanced flameproof structure, high reliability, convenient use and maintenance .
YB2 explosion-proof motor is used as fixed equipment for underground coal mine (non-mining work). It also used as drive device that applied to the place which composed of explosive mixture(combined air with factory lIB, T1-T4 temperature group flammable gas/steam. It is mainly used in coal mine, petroleum natural, petrochemical and chemical industries. In addition, it has been widely used in textile, metallurgy, city gas, transportation, grain and oil processing, paper making, medicine and other departments. As the main power equipment, explosion-proof motor is usually used to drive pumps, fans, compressors, conveyors and other transmission machinery.
Operating conditions:
Rated voltage:230v/400v,380v,415v,440v 660v 575v,690v 380/660v.
Rated frequency:50hz 60hz
Operation type:S1,S2,S3
Less than 1000 CHINAMFG above elevation.
The variation of temperatue to season shall be kept within -20-40 degrees.
Highest average R.H.in the enviroment;
(For motors in the mine well,when the aberage temperature is 25 degrees) not exceeding 95%
(For motors in factories,when the monthly aberage temperateu is not exceeding 25 degrees) the averge humidity should not be more tthan 90%
Explosion -proot mark:
The explosion proof marks of this series are EXDI EXDII AT4,EXDII BT4.
Structure of proteciton is ip54,ip55,ip65
Cooling type:IC411
Insulation class F,H.
Motor casing material:cast iron,aluminum
| Power: | 0.18kw-315kw | Voltage: | 230/400V,380V 400V 415V 660V 690V 1000V 6300V |
| Frequency: | 50/60hz | Enamelled Wire: | Copper Wire |
| Insulation Class: | F/B/H | Mounting Way: | B3 Foot/B5 Flange/B14/B34/B35 |
| Protection Grade: | IP54/IP55/IP44 | motor body : | cast iron/cast aluminum |
We have our own design and development team, we can provide customers with standard AC electric motors, We can also customize the single phase/three phase motors according to the special needs of customers. Currently our main motor products cover 3 – phase high – efficiency motors,general 3 – phase motors, single phase motors, etc.
The main motor ranges: IE3 / YE3, IE2 / YE2, IE1 / Y2,YB2/YB3,YEJ,YCT,YVF, Y, YS, MS, YC, YL, YY, MC, MY, ML motors.
American standard NEMA motors
Russian standard GOST ANP motors
ZheJiang type AEEF motors,YC motors
Why choose us?
Guarantee of our motors:18-24months
General elivery time:15-30days
Price of motors: Most reasonable during your all suppliers
Packing:Strong export cartons/wooden case/plywood cases/pallets
Payment way with your order: T/T,LC,DP,etc
Sample order: Acceptable
Shipment way: Sea ship,Air flight,Express way,Land transfer way.
If you are looking for new better supplier or purchase electric motors, welcome to feel free contact us now.
| Application: | Industrial, Universal, Power Tools |
|---|---|
| Operating Speed: | Constant Speed |
| Number of Stator: | Three-Phase |
| Samples: |
US$ 90/Piece
1 Piece(Min.Order) | Order Sample 0.37kw
|
|---|
| Customization: |
Available
|
|
|---|
.shipping-cost-tm .tm-status-off{background: none;padding:0;color: #1470cc}
|
Shipping Cost:
Estimated freight per unit. |
about shipping cost and estimated delivery time. |
|---|
| Payment Method: |
|
|---|---|
|
Initial Payment Full Payment |
| Currency: | US$ |
|---|
| Return&refunds: | You can apply for a refund up to 30 days after receipt of the products. |
|---|
What factors should be considered when selecting the right electric motor for a task?
When selecting the right electric motor for a task, several factors need to be considered to ensure optimal performance and compatibility. Here’s a detailed overview of the factors that should be taken into account:
- Load Requirements: The first consideration is understanding the specific load requirements of the task. This includes factors such as the torque or force needed to drive the load, the speed range required, and any variations in load that may occur. By accurately assessing the load requirements, you can determine the appropriate motor type, size, and characteristics needed to handle the task effectively.
- Motor Type: Different motor types are suited for specific applications. Common motor types include AC induction motors, brushless DC motors, brushed DC motors, and stepper motors. Each type has its own advantages and limitations in terms of speed range, torque characteristics, efficiency, control requirements, and cost. Choosing the right motor type depends on the task’s specific requirements and the desired performance.
- Power Supply: Consider the available power supply for the motor. Determine whether the application requires AC or DC power and the voltage and frequency range of the power source. Ensure that the motor’s power requirements align with the available power supply to avoid compatibility issues.
- Efficiency and Energy Consumption: Efficiency is an important factor to consider, especially for applications where energy consumption is a concern. Higher motor efficiency translates to lower energy losses and reduced operating costs over the motor’s lifetime. Look for motors with high efficiency ratings to minimize energy consumption and improve overall system efficiency.
- Environmental Factors: Assess the environmental conditions in which the motor will operate. Consider factors such as temperature, humidity, dust, and vibration. Some motors are specifically designed to withstand harsh environmental conditions, while others may require additional protection or enclosures. Choosing a motor that is suitable for the intended environment will ensure reliable and long-lasting operation.
- Control and Feedback Requirements: Determine whether the application requires precise control over motor speed, position, or torque. Some tasks may benefit from closed-loop control systems that incorporate feedback devices like encoders or sensors to provide accurate motor control. Evaluate the control and feedback requirements of the task and select a motor that is compatible with the desired control mechanism.
- Physical Constraints: Consider any physical constraints or limitations that may impact motor selection. These constraints may include space restrictions, weight limitations, mounting options, and mechanical compatibility with other components or equipment. Ensure that the chosen motor can physically fit and integrate into the system without compromising performance or functionality.
- Cost and Budget: Finally, consider the budget and cost constraints associated with the motor selection. Evaluate the initial purchase cost of the motor as well as the long-term operating costs, including maintenance and energy consumption. Strive to strike a balance between performance and cost-effectiveness to ensure the best value for your specific application.
By considering these factors, you can make an informed decision when selecting the right electric motor for a task. It is crucial to thoroughly analyze the requirements and match them with the motor’s specifications to achieve optimal performance, reliability, and efficiency.
Are there any emerging trends in electric motor technology, such as smart features?
Yes, there are several emerging trends in electric motor technology, including the integration of smart features. These trends aim to improve motor performance, efficiency, and functionality, while also enabling connectivity and advanced control capabilities. Here’s a detailed explanation of some of the emerging trends in electric motor technology:
- Internet of Things (IoT) Integration: Electric motors are becoming increasingly connected as part of the broader IoT ecosystem. IoT integration allows motors to communicate, share data, and be remotely monitored and controlled. By embedding sensors, communication modules, and data analytics capabilities, motors can provide real-time performance data, predictive maintenance insights, and energy consumption information. This connectivity enables proactive maintenance, optimized performance, and enhanced energy efficiency.
- Condition Monitoring and Predictive Maintenance: Smart electric motors are equipped with sensors that monitor various parameters such as temperature, vibration, and current. This data is analyzed in real-time to detect anomalies and potential faults. By implementing predictive maintenance algorithms, motor failures can be anticipated, enabling maintenance activities to be scheduled proactively. This trend reduces unplanned downtime, improves reliability, and optimizes maintenance costs.
- Advanced Motor Control and Optimization: Emerging electric motor technologies focus on advanced motor control techniques and optimization algorithms. These advancements allow for precise control of motor performance, adapting to changing load conditions, and optimizing energy efficiency. Additionally, sophisticated control algorithms enable motor systems to operate in coordination with other equipment, such as variable speed drives, power electronics, and energy storage systems, resulting in improved overall system efficiency.
- Energy Harvesting and Regenerative Features: Electric motors can harness energy through regenerative braking and energy harvesting techniques. Regenerative braking allows motors to recover and convert kinetic energy into electrical energy, which can be fed back into the system or stored for later use. Energy harvesting technologies, such as piezoelectric or electromagnetic systems, can capture ambient energy and convert it into usable electrical energy. These features enhance energy efficiency and reduce overall power consumption.
- Integration with Artificial Intelligence (AI) and Machine Learning (ML): The integration of electric motors with AI and ML technologies enables advanced motor control, optimization, and decision-making capabilities. AI and ML algorithms analyze motor performance data, identify patterns, and make real-time adjustments to optimize efficiency and performance. The combination of AI/ML with electric motors opens up possibilities for autonomous motor control, adaptive energy management, and intelligent fault detection.
- Miniaturization and Lightweight Design: Emerging trends in electric motor technology focus on miniaturization and lightweight design without compromising performance. This trend is particularly relevant for portable devices, electric vehicles, and aerospace applications. Advancements in materials, manufacturing processes, and motor design allow for smaller, lighter, and more powerful motors, enabling greater mobility, improved efficiency, and increased power density.
The integration of smart features in electric motor technology is driving advancements in connectivity, data analytics, predictive maintenance, advanced control, energy harvesting, AI/ML integration, and miniaturization. These trends are revolutionizing the capabilities and functionality of electric motors, making them more intelligent, efficient, and adaptable to various applications. As technology continues to evolve, electric motors are expected to play a crucial role in the ongoing transition towards smart and sustainable industries.
What industries and applications commonly use electric motors?
Electric motors are widely utilized in various industries and applications due to their versatility, efficiency, and controllability. Here’s a detailed overview of the industries and applications where electric motors are commonly employed:
- Industrial Manufacturing: Electric motors are extensively used in industrial manufacturing processes. They power machinery and equipment such as conveyor systems, pumps, compressors, fans, mixers, robots, and assembly line equipment. Electric motors provide efficient and precise control over motion, making them essential for mass production and automation.
- Transportation: Electric motors play a crucial role in the transportation sector. They are used in electric vehicles (EVs) and hybrid electric vehicles (HEVs) to drive the wheels, providing propulsion. Electric motors offer benefits such as high torque at low speeds, regenerative braking, and improved energy efficiency. They are also employed in trains, trams, ships, and aircraft for various propulsion and auxiliary systems.
- HVAC Systems: Heating, ventilation, and air conditioning (HVAC) systems utilize electric motors for air circulation, fans, blowers, and pumps. Electric motors help in maintaining comfortable indoor environments and ensure efficient cooling, heating, and ventilation in residential, commercial, and industrial buildings.
- Appliances and Household Devices: Electric motors are found in numerous household appliances and devices. They power refrigerators, washing machines, dryers, dishwashers, vacuum cleaners, blenders, food processors, air conditioners, ceiling fans, and many other appliances. Electric motors enable the necessary mechanical actions for these devices to function effectively.
- Renewable Energy: Electric motors are integral components of renewable energy systems. They are used in wind turbines to convert wind energy into electrical energy. Electric motors are also employed in solar tracking systems to orient solar panels towards the sun for optimal energy capture. Additionally, electric motors are utilized in hydroelectric power plants for controlling water flow and generating electricity.
- Medical Equipment: Electric motors are crucial in various medical devices and equipment. They power surgical tools, pumps for drug delivery and fluid management, diagnostic equipment, dental drills, patient lifts, wheelchair propulsion, and many other medical devices. Electric motors provide the necessary precision, control, and reliability required in healthcare settings.
- Robotics and Automation: Electric motors are extensively used in robotics and automation applications. They drive the joints and actuators of robots, enabling precise and controlled movement. Electric motors are also employed in automated systems for material handling, assembly, packaging, and quality control in industries such as automotive manufacturing, electronics, and logistics.
- Aerospace and Defense: Electric motors have significant applications in the aerospace and defense sectors. They are used in aircraft for propulsion, control surfaces, landing gear, and auxiliary systems. Electric motors are also employed in military equipment, drones, satellites, guided missiles, and underwater vehicles.
These are just a few examples of the industries and applications where electric motors are commonly used. Electric motors provide a reliable, efficient, and controllable means of converting electrical energy into mechanical energy, making them essential components in numerous technologies and systems across various sectors.
editor by CX 2023-12-06
China wholesaler NEMA 143T 110V 220V 5HP TEFC Single Phase electric motor for Air Compressor near me shop
Warranty: 3months-1year
Model Number: F56C
Type: Induction Motor
Frequency: 60HZ
Phase: Single-phase
Protect Feature: Totally Enclosed
AC Voltage: 115-230/208V
Efficiency: IE 2
Power: 1HP-10HP
ENCL.: ODP
Mounting: C flange face and removable
Packaging Details: woodbox
Port: HangZhou
NEMA 143T 110V 220V 5HP TEFC Single Phase electric motor for Air Compressor HP1HP-10HPFrameNEMA Rolled Steel, 56–215TStart TorqueTst=250%EndosureTEFCInsulationF. Certification Detailed Images Why Choose Us WHY CHOOSE JIRUNA.Certificates passed:tests passed for most of our motors and can supply reports.
B.Fast feedback for customers:24 hours reply for all customers’ inquiries. C. Competitive prices. D. Quality guarantee:We have shipped much motors to Italy, Spain, and other European and USA customers with high quality.E. Fast and Timely delivery:Usually 10-15 days for goods production.F. Professional Technical support and After-sale service.G.Customized service for kind of motor according to your requirement.
Our Company WorkshopStamping Machinery, CNC-Machinery, Vacuum Pressure Impregnating, Plating Machinery. and so on.
FAQ Q1: What kind motors you can provide?A1: For now, we mainly provide permanent magnet brush dc motors, brushless dc motor, dc gear motor, micro dc motor, ac gear motor, planetary gear motor, with diameter range in 42~110mm. NEMA dc motor. NEMA dc Motor. stainless steel motor
Q2: Is there a MOQ for your motors?A2: No. we can accept 1 pcs for sample making for your testing,and the price for sample making will have 30% to 50% difference based on different style.
Q3: Could you send me a price list?A3: For all of our motors, they are customized based on different requirements like power, voltage, gear ratio, rated torque and shaft diameter etc. The price also varies according to different order qty. So it’s really difficult for us to provide a price list. If you can share your detailed specification and order qty, we’ll see what offer we can provide.
Q4: Are you motors reversible?A4: Yes, nearly all dc and ac motor are reversible. We have technical people who can teach how to get the function by different wire connection.
Q5:How about your delivery time? A5: For micro brush dc gear motor, the sample delivery time is 2-5 days, bulk delivery time is about 15-20 days, depends on the order qty. For brushless dc motor, the sample deliver time is about 10-15 days; bulk time is 15-20 days.Please take the sales confirmation for final reference.
Packing & Delivery THE SAMPLE BY EXPRESS OR AIR
LCL=LESS THAN CONTAINER LOAD, FCL=FULL CONTAINER LOAD, BY SHIPMENT
Recommend Products
How to Maximize Gear Motor Reliability
A gearmotor is a mechanical device used to transmit torque from one location to another. As its name implies, it is designed to rotate one object relative to another. Its main use is to transmit torque from one point to another. The most common types of gear motors are: worm, spur, and helical. Each of these has specific functions and can be used for a variety of applications. Reliability is also an important factor to consider when choosing a gearmotor.
Applications of a gear motor
Despite its small size, a gear motor has many applications. These include heavy machinery lifts, hospital beds, and power recliners. It is also found in many everyday products, such as electromechanical clocks and cake mixers. Its versatility allows it to produce a high force from a small electric motor. Here are some of its most common uses. You can also find a gear motor in many household appliances and vehicles.
Before selecting a gearmotor, consider the specifications of the machine you need to power. You should consider its size, weight, and ambient conditions, which include temperature regimes, noise levels, and contaminating sources. You should also take into account the envelope size, mounting method, and orientation. Other considerations include the expected service life, maintenance scope, and control type. The most suitable gearmotor for your specific application will be one that can handle the load.
The motor and gearbox types can be mixed and matched, depending on the application. A three-phase asynchronous motor and a permanent magnet synchronous servomotor are common choices for these devices. The type of motor and gearbox combination you choose will determine the power supply, the efficiency of the motor, and cost. Once you understand the application, it will be easy to integrate a gear motor into your system.
When used in industrial applications, gear motors are effective for reducing the speed of rotating shafts. One third of all industrial electric motor systems use gearing to reduce output speed. They can also save energy, which benefits the workers who operate them. In fact, industrial electric motor systems are responsible for nearly one-tenth of the carbon dioxide emissions that are produced by fossil-fueled power plants. Fortunately, efficiency and reliability are just two of the benefits of using gear motors.
Types
Before choosing a gearmotor, it is important to understand its specifications. The key factors to consider are the size, weight, and noise level of the gearmotor. Additionally, the power, torque, and speed of the motor are important factors. Specifications are also important for its operating environment, such as the temperature and the level of ingress protection. Finally, it is important to determine its duty cycle to ensure it will operate properly. To choose a suitable gearmotor, consult the specifications of your application.
Some common applications of gearmotors include packaging equipment, conveyors, and material handling applications. They also come with several advantages, including their ability to control both position and speed. This makes them ideal for applications where speed and positioning are crucial. Parallel-shaft gear units, for instance, are commonly used in conveyors, material handling, and steel mills. They are also able to operate in high-precision manufacturing. For these reasons, they are the most popular type of gearmotor.
There are three common types of gears. Helical gears have teeth that are inclined at 90 degrees to the axis of rotation, making them more efficient. Helicoidal gears, meanwhile, have a lower noise level and are therefore preferred for applications requiring high torque. Worm gears are preferred for applications where torque and speed reduction are important, and worm gears are suited for those conditions. They also have advantages over spur gears and worm gears.
The application of a gear motor is almost limitless. From heavy machine lifts to hospital bed lifting mechanisms, gear motors make it possible to use a small rotor at a high speed. Their lightweight construction also allows them to move heavy loads, such as cranes, but they do so slowly. Gear motors are an excellent choice in applications where space is an issue. A few common applications are discussed below. When choosing a gear motor, remember to choose the best size and application for your needs.
Functions
A gearmotor’s speed is directly proportional to the gear ratio. By dividing the input speed by the gear ratio, the output speed can be determined. Gear ratios above one reduce speed, while gear ratios below one increase speed. Efficiency of a gearmotor is defined as its ability to transfer energy through its gearbox. This efficiency factor takes into account losses from friction and slippage. Most gearmotor manufacturers will provide this curve upon request.
There are several factors that must be considered when choosing a gearmotor. First, the application must meet the desired speed and torque. Second, the output shaft must rotate in the desired direction. Third, the load must be properly matched to the gearmotor. Lastly, the operating environment must be considered, including the ambient temperature and the level of protection. These details will help you find the perfect gearmotor. You can compare various types of gear motors on this page and choose the one that will meet your needs.
The micro-DC gear motor is one of the most versatile types of geared motors. These motors are widely used in intelligent automobiles, robotics, logistics, and the smart city. Other applications include precision instruments, personal care tools, and cameras. They are also commonly found in high-end automotives and are used in smart cities. They also find use in many fields including outdoor adventure equipment, photography equipment, and electronics. The benefits of micro-DC gear motors are many.
The main function of a gear motor is to reduce the speed of a rotating shaft. Small electric clocks, for example, use a synchronous motor with a 1,200-rpm output speed to drive the hour, minute, and second hands. While the motor is small, the force it exerts is enormous, so it’s crucial to ensure that the motor isn’t over-powered. There is a high ratio between the input torque and the output torque.
Reliability
The reliability of a gear motor is dependent on a number of factors, including material quality, machining accuracy, and operating conditions. Gear failure is often more serious than surface fatigue, and can compromise personal safety. Reliability is also affected by the conditions of installation, assembly, and usage. The following sections provide an overview of some important factors that impact gear motor reliability. This article provides some tips to maximize gear motor reliability.
First and foremost, make sure you’re buying from a reliable supplier. Gear motors are expensive, and there is no standardization of the sizes. If a gear breaks, replacing it can take a lot of time. In the long run, reliability wins over anything. But this doesn’t mean that you can ignore the importance of gears – the quality of a gear motor is more important than how long it lasts.
Cost
The cost of a gear motor is relatively low compared to that of other forms of electric motors. This type of motor is commonly used in money counters, printers, smart homes, and automation equipment. A DC gear motor is also commonly used in automatic window machines, glass curtain walls, and banknote vending machines. There are many advantages to using a gear motor. Here are a few of them. Read on to learn more about them.
Speed management is another benefit of a gear motor. The motors tend to have less wear and tear than other motors, which means less frequent replacements. Additionally, many gear motors are easy to install and require less maintenance, which also helps reduce the overall cost of ownership. Lastly, because noise is a common concern for many electronic OEMs, DC gear motors are often quieter than their counterparts. For these reasons, they are often used in industrial settings.
Another advantage of an electric gear motor is its size and power. They are typically designed for 12V, 24V, and 48V voltages and 200-watt power. Their rated speed is 3000 rpm and their torque is 0.64 Nm. They are also more reliable than their AC counterparts and are ideal for many industrial applications. They have a high ratio of three to two, which makes them ideal for a variety of applications.
A gear motor is an electric motor that is coupled with a gear train. It uses AC or DC power, and is often called a gear reducer. The main purpose of these gear reducers is to multiply torque, while maintaining compact size and overall efficiency. However, the efficiency of a gear motor is also affected by ambient temperature and lubricants. If the gear motor is installed in the wrong location, it may be ineffective and result in premature failure of the machine.
China Standard 3 phase industry IE2 380V ac electric motor air compressor asynchronous motors with Hot selling
Warranty: 3months-1year, 1 Year
Model Number: 200L2-2-55KW
Type: Asynchronous Motor
Frequency: 50Hz/60Hz
Phase: Three-phase
Protect Feature: Totally Enclosed
AC Voltage: 380V
Efficiency: IE 2
Product Name: Electric Motor
Power: 55kw ac motor
Rated Voltage: 220/380V 230/440V 380/660V 400/690V
Current: 102.6A
Protection class: IP54/IP55
Speed: 2950rpm
Rated Torque: 2.3nm
Service factor: 1.2
Application: use for screw air compressor
Certification: CCC, ce, RoHS
Packaging Details: Plywood carton or pallet
3 phase industry IE2 380V ac electric motor air compressor asynchronous motors
Air compressor motor Information
Power
55KW ac motor
Protection class
IP54/IP55
Description
3 phase motors
Capacity
9.2m3/min
Pressure
8 bar/116psi
Brand
Airstone(Customized logo is avaliable)
Warranty
1 Years
1.Accept customize airend service, using CZPT or CZPT airend(no vabiration, no noise,large rotor,low speed,direct connection, large gas production.)
2.Adopt the latest standard: GB186~13 0571 88828 13858117778-2012 small and medium asynchronous motor energy efficiency limit value and energy efficiency grade.Energy efficiency rating IE2/IE3, protection class IP23/IP54/IP55, service factor 1.2,insulation class F,speed 2960r/min.
3.Direct drive compressor adopt high-precision flexible coupling, transmission ratio 1:1, low energy consumption and high efficiency.
4.Stainless steel tubing and air tube, high temperature resistance(400℃=725°F),low temperature, resistance(-200℃=518°F), high pressure resistance=long life(80 years), no leakage maintenance-free compliance with CE, IOS9001 and energy-saving certification. Long-term work,stable displacement and pressure, no collision, no failure rate.
The application range 3 phase motors of screw air compressor is very wide: heavy,light industry, mining, hydropower, seaport, engineering construction, oil and gas fields, railways, transportation, shipbuilding, energy, military industry and other industries.
HangZhou Xihu (West Lake) Dis. Mechanical Equipment Co., Ltd. is located in B district of lianhua industrial park, HangZhou city, ZheJiang province. The company was founded in May 2018, covers an area of more than 150 acres, and has a factory building of more than 6,000 square meters. The company has more than 300 fixed employees, more than 50 skilled workers, and more than 40 sets of large-scale production equipment.The company has a complete equipment production system. In order to strengthen the integration of the industry, the company passed the ISO9001:2008 international quality management system verification at the end of 2018. After the company’s unity, positive and facing fierce market competition, the company is relying on its own advantages to integrate external resources, optimize pioneering and innovation, and move forward in the direction of diversified business and diversified operations. The company is mainly engaged in the production of screw air compressors and spare parts. The main products are fix speed screw air compressor,variable frequency speed screw air compressor, permanent magnet variable frequency speed screw air compressor and two-stage screw air compressor. At the end of 2018, the company joined forces with famous school designers to develop integrated screw compressors. The pressure range is 0.4mpa-1.6mpa and the power is 4kw-315kw. It can be customized to meet the requirements of different climate buyers in different countries.
Neutral packing & original Packing & our packing are available for the 55KW electric motor.
Q1. How about the package for this 3 phase motors?A: Generally, we pack our goods in neutral wooden case. If you have legally registered patent, we can pack the goods in your branded boxes after getting your authorization letters.
Q2. What is your terms of payment?A: 100%T/T in advance, L/C, Paypal before delivery. We’ll show you the photos of the products and packages before you pay the balance.
Q3. What is your terms of the ac motor delivery?A: EXW, FOB, CFR, CIF, DDU are available.
Q4. How about your delivery time for this electric motor?A: Generally, it will take 7 to 15 working days after receiving your advance payment. The specific delivery time depends on the items and the quantity of your order.
Q5. Can you produce the 3 phase motors according to the samples?A: Yes, we can produce by your samples or technical drawings. We can build the molds and fixtures.
Q6. What is your sample policy?A: We can supply the ac motor sample if we have ready parts in stock, but the customers have to pay the sample cost and the courier cost.
Q7. Do you test all your electric motor before delivery?A: Yes, we have 100% test before delivery, don’t worry about the 3 phase motors quality.
Q8: How do you make our business long-term and good relationship?A:1. We keep good quality and competitive price to ensure our customers benefit; 2. We respect every customer as our friend and we sincerely do business and make friends with them, no matter where they come from.
How to Maximize Gear Motor Reliability
A gearmotor is a mechanical device used to transmit torque from one location to another. As its name implies, it is designed to rotate one object relative to another. Its main use is to transmit torque from one point to another. The most common types of gear motors are: worm, spur, and helical. Each of these has specific functions and can be used for a variety of applications. Reliability is also an important factor to consider when choosing a gearmotor.
Applications of a gear motor
Despite its small size, a gear motor has many applications. These include heavy machinery lifts, hospital beds, and power recliners. It is also found in many everyday products, such as electromechanical clocks and cake mixers. Its versatility allows it to produce a high force from a small electric motor. Here are some of its most common uses. You can also find a gear motor in many household appliances and vehicles.
Before selecting a gearmotor, consider the specifications of the machine you need to power. You should consider its size, weight, and ambient conditions, which include temperature regimes, noise levels, and contaminating sources. You should also take into account the envelope size, mounting method, and orientation. Other considerations include the expected service life, maintenance scope, and control type. The most suitable gearmotor for your specific application will be one that can handle the load.
The motor and gearbox types can be mixed and matched, depending on the application. A three-phase asynchronous motor and a permanent magnet synchronous servomotor are common choices for these devices. The type of motor and gearbox combination you choose will determine the power supply, the efficiency of the motor, and cost. Once you understand the application, it will be easy to integrate a gear motor into your system.
When used in industrial applications, gear motors are effective for reducing the speed of rotating shafts. One third of all industrial electric motor systems use gearing to reduce output speed. They can also save energy, which benefits the workers who operate them. In fact, industrial electric motor systems are responsible for nearly one-tenth of the carbon dioxide emissions that are produced by fossil-fueled power plants. Fortunately, efficiency and reliability are just two of the benefits of using gear motors.
Types
Before choosing a gearmotor, it is important to understand its specifications. The key factors to consider are the size, weight, and noise level of the gearmotor. Additionally, the power, torque, and speed of the motor are important factors. Specifications are also important for its operating environment, such as the temperature and the level of ingress protection. Finally, it is important to determine its duty cycle to ensure it will operate properly. To choose a suitable gearmotor, consult the specifications of your application.
Some common applications of gearmotors include packaging equipment, conveyors, and material handling applications. They also come with several advantages, including their ability to control both position and speed. This makes them ideal for applications where speed and positioning are crucial. Parallel-shaft gear units, for instance, are commonly used in conveyors, material handling, and steel mills. They are also able to operate in high-precision manufacturing. For these reasons, they are the most popular type of gearmotor.
There are three common types of gears. Helical gears have teeth that are inclined at 90 degrees to the axis of rotation, making them more efficient. Helicoidal gears, meanwhile, have a lower noise level and are therefore preferred for applications requiring high torque. Worm gears are preferred for applications where torque and speed reduction are important, and worm gears are suited for those conditions. They also have advantages over spur gears and worm gears.
The application of a gear motor is almost limitless. From heavy machine lifts to hospital bed lifting mechanisms, gear motors make it possible to use a small rotor at a high speed. Their lightweight construction also allows them to move heavy loads, such as cranes, but they do so slowly. Gear motors are an excellent choice in applications where space is an issue. A few common applications are discussed below. When choosing a gear motor, remember to choose the best size and application for your needs.
Functions
A gearmotor’s speed is directly proportional to the gear ratio. By dividing the input speed by the gear ratio, the output speed can be determined. Gear ratios above one reduce speed, while gear ratios below one increase speed. Efficiency of a gearmotor is defined as its ability to transfer energy through its gearbox. This efficiency factor takes into account losses from friction and slippage. Most gearmotor manufacturers will provide this curve upon request.
There are several factors that must be considered when choosing a gearmotor. First, the application must meet the desired speed and torque. Second, the output shaft must rotate in the desired direction. Third, the load must be properly matched to the gearmotor. Lastly, the operating environment must be considered, including the ambient temperature and the level of protection. These details will help you find the perfect gearmotor. You can compare various types of gear motors on this page and choose the one that will meet your needs.
The micro-DC gear motor is one of the most versatile types of geared motors. These motors are widely used in intelligent automobiles, robotics, logistics, and the smart city. Other applications include precision instruments, personal care tools, and cameras. They are also commonly found in high-end automotives and are used in smart cities. They also find use in many fields including outdoor adventure equipment, photography equipment, and electronics. The benefits of micro-DC gear motors are many.
The main function of a gear motor is to reduce the speed of a rotating shaft. Small electric clocks, for example, use a synchronous motor with a 1,200-rpm output speed to drive the hour, minute, and second hands. While the motor is small, the force it exerts is enormous, so it’s crucial to ensure that the motor isn’t over-powered. There is a high ratio between the input torque and the output torque.
Reliability
The reliability of a gear motor is dependent on a number of factors, including material quality, machining accuracy, and operating conditions. Gear failure is often more serious than surface fatigue, and can compromise personal safety. Reliability is also affected by the conditions of installation, assembly, and usage. The following sections provide an overview of some important factors that impact gear motor reliability. This article provides some tips to maximize gear motor reliability.
First and foremost, make sure you’re buying from a reliable supplier. Gear motors are expensive, and there is no standardization of the sizes. If a gear breaks, replacing it can take a lot of time. In the long run, reliability wins over anything. But this doesn’t mean that you can ignore the importance of gears – the quality of a gear motor is more important than how long it lasts.
Cost
The cost of a gear motor is relatively low compared to that of other forms of electric motors. This type of motor is commonly used in money counters, printers, smart homes, and automation equipment. A DC gear motor is also commonly used in automatic window machines, glass curtain walls, and banknote vending machines. There are many advantages to using a gear motor. Here are a few of them. Read on to learn more about them.
Speed management is another benefit of a gear motor. The motors tend to have less wear and tear than other motors, which means less frequent replacements. Additionally, many gear motors are easy to install and require less maintenance, which also helps reduce the overall cost of ownership. Lastly, because noise is a common concern for many electronic OEMs, DC gear motors are often quieter than their counterparts. For these reasons, they are often used in industrial settings.
Another advantage of an electric gear motor is its size and power. They are typically designed for 12V, 24V, and 48V voltages and 200-watt power. Their rated speed is 3000 rpm and their torque is 0.64 Nm. They are also more reliable than their AC counterparts and are ideal for many industrial applications. They have a high ratio of three to two, which makes them ideal for a variety of applications.
A gear motor is an electric motor that is coupled with a gear train. It uses AC or DC power, and is often called a gear reducer. The main purpose of these gear reducers is to multiply torque, while maintaining compact size and overall efficiency. However, the efficiency of a gear motor is also affected by ambient temperature and lubricants. If the gear motor is installed in the wrong location, it may be ineffective and result in premature failure of the machine.
China best GOST Standard Asynchronous AC Electric Motor for Blower Axial Fan Water Pump Air Compressor Gear Box with Best Sales
Item Description
GOST Normal Asynchronous AC Electric powered Motor for Blower Axial Fan Water Pump Air Compressor Gear Box
| Frame size | 56A- 355M |
| Pole | two-10 |
| Rated voltage | 380V |
| Frequency | 50Hz |
| Power | .18kw-315Kw |
| Protection degree | IP54 |
| Cooling method | IC411 |
| Insulation class | F |
| Ambient Temperature | -15°C~40°C |
| Altitude | not exceed 1000 Meter |
| Working Duty | S1(Constant) |
Item Description
Manufacturing facility and Production Line
Software fields
machine equipment, water pump, blower, compressor, and transportation, print, agriculture, food and much more industries.
Certifications
FAQ
Q: What is your MOQ of this product?
A: 5PCS.
For the first time cooperation, we acknowledge demo sample buy.
Q: What is your payment conditions?
A: 30% T/T deposit, 70% harmony just before cargo or L/C at sight.
Q: What is actually the delivery time?
A: twenty five-thirty times following obtaining your L/C or T/T deposit.
Q: Can we utilised our personal manufacturer on motors ?
A: Certain, we can supply OEM support,
manufacture with your authorized manufacturer.
Q: How lengthy is your guarantee?
A: 12 months right after getting B/L.
Staff
Motor Summary
An AC motor is a typical kind of electric motor that is pushed by alternating recent. As the most productive sensible motors for each day industrial programs (as effectively as hobbyist projects, home products, and all other skilled tools and buyer items), AC motors provide a comparatively successful method of making mechanical power from a basic electrical input signal.
DC motors use strength from batteries or other producing sources that provide a continuous voltage. A DC motor is composed of a number of components, the most well-known of which incorporate bearings, shafts, and gearboxes or gears. DC motors give better velocity variation and control and produce much more torque than AC motors. The two sorts of DC motors incorporate Brushed motors: Brushed motors are one of the oldest types and are internally commutated motors pushed by DC current. A brushed motor is made up of a rotor, brushes, and a shaft. The demand and polarity of the brushes control the path and velocity of the motor. Brushless Motors: In current a long time, brushless motors have become well-known for numerous purposes, largely due to the fact of their performance. Brushless motors are constructed in the same way as brushed motors, minus the brushes of system. Brushless motors also consist of focused circuitry to control speed and path. In brushless motors, magnets are mounted about the rotor, an efficiency-boosting configuration.
China Professional Three Phase Tk Large Size Synchronous Low Speed High Voltage Electric Motor for Air Compressor wholesaler
Product Description
The three-stage synchronous motor for TK air compressor complies with relevant IEC global specifications. The synchronous motor excitation system employs a static thyristor excitation unit. The motor permits immediate start at full force, and can also be stepped down when the grid capability does not allow complete strain start off. This series of motors has the rewards of compact structure, high efficiency, low sound, lower vibration, substantial trustworthiness, convenient set up and servicing.
The high-voltage synchronous motor of this series has the defense diploma of IP00 and the CZPT strategy is IC01. If other safety amounts and CZPT strategy specifications are adopted, it can be negotiated with the consumer. The rated voltage of this sequence of motors is 6000 volts, and the allowable voltage of 10000 volts is inside ±5%. The rated frequency of the power supply is fifty Hz and the rated power element is .9 (leading).
TK series massive three-stage synchronous motor is mostly utilised to push reciprocating (piston) air compressors. It is ideal for motors of CZPT and fertilizer products, and can also be employed to generate pumps, enthusiasts and other basic mechanical products.
Motor Title: Substantial-voltage synchronous motor for TK air compressor
Electrical power assortment: 250KW-5000KW
Pace variety: two hundred-one thousand r/min
Rated voltage: 380V/3000V/6000V/10000V
Rated frequency: 50HZ/60HZ
Power factor: .9
Insulation course: F
Security degree: IP00/IP21/IP23
Set up method: IM7311/IM5710
Operating program: S1
Excitation mode: static thyristor, other excitation techniques can also be used
Link: Y
Cooling strategy: IC01. Other varieties of motors can also be produced in accordance to person demands, this sort of as duct ventilation and air and air cooling.
Altitude: no a lot more than 1000m
Slip rings can be divided into widespread construction or slip ring constructive stress air flow.
This type of motor is appropriate for use in environments exactly where the ambient air temperature does not CZPT forty ° C and there is no significant dust, the least ambient air temperature is -15 ° C, and there is no corrosive and explosive gasoline in the air (which can also be manufactured into a moist warmth or substantial-altitude motor).
TK series air compressor motors have sophisticated electrical power aspect (which can boost grid power element), higher effectiveness, higher security and high overload functionality, and have the performance that the pace does not modify with the load, specifically when the velocity is reduce than 600r/min. The performance is considerably greater than the asynchronous motor of the identical velocity.
Our company’s motor production manufacturing facility adheres to the notion of inexperienced, successful and energy-preserving production service, pays attention to the harmonious advancement of internal and exterior environment, builds environmentally welcoming motor production enterprises, strictly implements motor regular procedure, and selects high-high quality strength-conserving supplies to make sure the quality of motor merchandise.
The business insists on supplying large-good quality motor merchandise and solutions to customers, and has won high praise from a lot of domestic and overseas buyers. The firm will get several overseas merchants to pay a visit to our factory each and every year, and create a good cooperative romantic relationship by way of on-web site inspection of our manufacturing facility. Our company always welcomes buyers to pay a visit to our manufacturing unit.
1. The outer packaging of the products are all common export-oriented wood plywood packaging.
two, the merchandise packaging is guarded by moisture, water plastic gentle packaging
3. For goods with specific transportation demands (such as temperature, fragile, variability, and effortless to get moist), the packaging defense steps will be strengthened, and the target mark will be printed on the deal.
4. There are clear indications and symbols on the packing box that should be paid interest to in the course of transportation and storage (these kinds of as place, dampness, rain, shockproof, lifting situation, and so forth.).
The rotor of a reluctance motor consists of a sound forged steel element with a convex toothed rack. Their beginning method is equivalent to an induction motor, but it operates like a synchronous motor. Generally, their rotors have much less poles than stators, which minimizes torque ripple and prevents excellent pole alignment, as no torque is produced in that area. Reluctance motors range in electricity rankings from a couple of watts to about 22 kilowatts.
AC motors vary from numerous other types of motors, specially some of the much more acquainted DC (direct present) motors, by many important standards. The most standard of these is the fact that an AC motor depends completely on the alternating current all around its circuit to produce powerful mechanical energy. We’ll go over this unique procedure in much more depth in the following sections of this guide.
China OEM Ye3 0.75kw-4p Three-Phase AC Asynchronous Squirrel-Cage Induction Electric Motor for Water Pump, Air Compressor near me shop
Item Description
> Product Introduction
Gphq Y2/YE2 15HP/CV 11kw Cast Iron 3 Phase Electrical AC Motor
Y2/ YE2 Collection Solid Iron Three Section Induction Motor is specially created for European market place, whose terminal box is located on the leading of motor.They are totally enclosed and admirer-cooling designed. They are newly created in conformity with the relevant demands / rules of IEC requirements.
For the Connection Product of 2p 4p 6p 8p Y2 motor, please refer to the Identify Plate on the motor (The Y Connection is adopted by motors’ Output equivalent or under 3kW The Delta-Link is adopted by motors’ Output above 4kW).
| Power: | .55kw-315kw | Voltage: | 380/415/440V( can can carried out as your need) |
| Frequency: | 50/60hz | Enamelled Wire: | Copper Wire (Can Done Aluminum wire as Your Need) |
| Insulation Course: | F | Mounting Way: | B3 Foot /B5 Flange /B35 Foot and Flange |
| Security Grade: | IP55 | motor entire body : | solid iron physique of ac motor |
> Applications
Common location and machine with no special requirments, for example: equipment instruments, pumps, enthusiasts, transportation equipment, mixer, agriculture equipment, food equipment, agitator, air compressor and so forth. We also can supply aluminum housing variety for body dimensions below the regular of IEC.
> Our Electrical Motor Advantages
1. Wonderful top quality of supplies(Cold silicon steel/a hundred% copper wire/ Aluminum body)
two.Colourful wiring
three.Obvious nameplate
4.Reliable bundle
5.Higher efficiency, low sounds
six.Best materials make greatest efficiency
FAQ
1, Q:what is your MOQ for ac synchronous motor ?
A: 5pc is okay for each and every kind electrical motor
two, Q: What about your warranty for your 3 phase motor?
A: 1 yr ,but except male-produced wrecked
three, Q: which payment way you can settle for ?
A: TT, western union .
four, Q: how about your payment way ?
A: a hundred%payment in innovative considerably less $5000 ,30% payment in advanced payment , 70% payment just before sending in excess of $5000.
5, Q: how about your packing of induction motor ?
A: carton or plywood scenario ,if considerably less 1 container , we can pack all goods with pallet for little dimensions motor
six, Q: What details ought to be provided, if I buy electric powered ac motor from you ?
A: rated power, pace or pole ,variety ,voltage , mounting way , quantity , if far more is greater.
The rotor of a reluctance motor is made up of a strong cast steel part with a convex toothed rack. Their commencing process is similar to an induction motor, but it operates like a synchronous motor. Usually, their rotors have fewer poles than stators, which minimizes torque ripple and prevents ideal pole alignment, as no torque is made in that place. Reluctance motors variety in electrical power rankings from a couple of watts to about 22 kilowatts.
Synchronous motors operate at a pace that is synchronous with the frequency of the mains present. This means that in the constant-condition of the motor, the rotation of the shaft is synchronized with the frequency of the supply present. The interval of rotation of the shaft is equal to the number of AC cycles. The stator of a synchronous motor has polyphase AC electromagnets. These electromagnets make a magnetic field that rotates in synchrony with the recent in the wire. The rotor geared up with long term magnets or electromagnets rotates synchronously with the stator magnetic field to sort the 2nd synchronous rotating magnetic discipline of the AC motor.
China high quality Ye3 220kw-6p Three-Phase AC Asynchronous Squirrel-Cage Induction Electric Motor for Water Pump, Air Compressor near me factory
Merchandise Description
The YE3 series quality performance a few-phase asynchronous motor is inline with IE3 effectiveness standard in the provisions of IEC60034-30-2008.And the enhancement of the effectiveness in its layout is in line with the state’s demands on the energy preserving and use minimizing of the production sector.
YE3 collection high quality effectiveness a few-phase asynchronous motor with the mounting dimension in accordance with common IEC60034,it has good functions like the best possible construction, desirable visual appeal, lower sounds, high performance, substantial safety course as properly as substantial insulation class.YE3 sequence quality efficiency three-stage asynchronous motor can be broadly employed in various varieties of common use machineries like enthusiasts, pumps, equipment instruments, compressors, transportation and so on, and can also be utilized in the dangerous areas with oil and chemical, steel plants, mining business.
Detail:
Running circumstances
Ambient temperature: -20senti degree≤ 0≤ 40senti degree
Altitude:decrease than a thousand meters earlier mentioned sea stage
Temperature and Insulation class
Motors are dependent on F (155ºC) ,B (80K),
to keep motor existence and dependability
Cooling and Air flow
Entirely enclosed self fan cooling(TEFC).
Motor is mounted with auxiliary stream sort
Plastic fan which is complying with
the provisions of 60034-6 IEC Ic411
Insulation class
Motor security course is Ip55 which
can be used for dust or humidity
surroundings, and we can supply
a greater degree of security of motor
Motor defense
AS need, motor can be set up of PTC,
Pt100 and other winding resistance and
Bearing temperature measurement and
Security unit.
Voltage and frequency
The common voltage is 380V/50Hz.
which can be made between
200-600V,in the case of deviation
5%, the motor still can function excellent.
Vibration
Vibration pace of Ye3 collection motor
in the no-load is in line with course A,
specific requirement, we can supply
course B.
Terminals block box spot
The terminal block box is on the
top or 1 the correct aspect as the regular
Ye2 series motor.
Good quality assurance
From style to produce factory,
we strictly comply with the ISO9001 high quality
certification program and processes.
Polyphase motors can be possibly two-section or 3-section motors. They function like single-period induction motors, but both one-section and polyphase motors operate on a rotating magnetic discipline. Their rotating magnetic fields are produced by two- or 3-section currents passing by way of two or much more sets of coils. The rotating magnetic field produces torque. Polyphase motors are used in apps that demand large electrical power, these kinds of as the energy travel of compressors, hydraulic pumps, air conditioning compressors, and irrigation pumps.
AC motors are also diverse from DC motors because most AC motors do not incorporate brushes. This implies that upkeep and components substitute requirements for AC motors are inclined to be substantially lowered, with most customers typically anticipating a for a longer time common lifespan. As opposed to DC motors, the output pace of many varieties of AC motors is usually identified by inverter manage – once more, we will briefly outline a selection of likely variants on the simple AC motor product.