Tag Archives: low speed gear motor

China high quality 45mm 12V High Torque Low Speed Planetary Gear Motor with Good quality

Product Description

45mm 12V High Torque Low Speed Planetary Gear Motor

Gearbox data:
 

Number of stages 1stages reduction 2 stages reduction 3 stages reduction 4 stages reduction 5 stages reduction
Reduction ratio 3.7,5.2 13.7,19.2,26.9 50.9,71.2,99.5,139 188,264,369,516,721 669,977,1367,1911,2672,3736,
gearbox length ” L” mm 26.4 32.6 38.9 45.3 52.5
Max.Running torque 3.0Kgf · cm 6.0Kgf · cm 8.0Kgf · cm 12.0Kgf · cm 20Kgf · cm
Max. Gear breaking torque 9.0Kgf · cm 18.0Kgf · cm 24Kgf · cm 36Kgf · cm 60Kgf · cm
Max. Gearing efficiency 90% 81% 73% 65%

Motor data:
 

Motor name Rated volt.v No load Load torque Stall torque
Current Speed Current Speed Torque Output power Torque Current
mA r/min mA r/min gf · cm W gf · cm mA
RS-555123 12 ≤220 45 12 ≤350 6 24 ≤70 3 24 ≤110 45 24 ≤180 6000 ≤1000 4500 300 13.5 1200 4000
       1,This table lists some motors parameters, others please refer to specific parameters of rs-555.htm”
       2,Afier connecting motor and gearbox which is named gearmotor the output torque:motor torque X reduction ratio X        gearing efficiency;output speed:motor speed / reduction ratio.

Company Introduction

 

Output Speed: 0.5rpm—2000rpm
Gears: Metal Gear,Powder Metallurgy
Gearing Arrangement: Planetary
Power: DC
Drive Motor: Low Noise
Motor: with Gearbox
Customization:
Available

|

Customized Request

Motor

Dynamic Modeling of a Planetary Motor

A planetary gear motor consists of a series of gears rotating in perfect synchrony, allowing them to deliver torque in a higher output capacity than a spur gear motor. Unlike the planetary motor, spur gear motors are simpler to build and cost less, but they are better for applications requiring lower torque output. That is because each gear carries the entire load. The following are some key differences between the two types of gearmotors.

planetary gear system

A planetary gear transmission is a type of gear mechanism that transfers torque from one source to another, usually a rotary motion. Moreover, this type of gear transmission requires dynamic modeling to investigate its durability and reliability. Previous studies included both uncoupled and coupled meshing models for the analysis of planetary gear transmission. The combined model considers both the shaft structural stiffness and the bearing support stiffness. In some applications, the flexible planetary gear may affect the dynamic response of the system.
In a planetary gear device, the axial end surface of the cylindrical portion is rotatable relative to the separating plate. This mechanism retains lubricant. It is also capable of preventing foreign particles from entering the planetary gear system. A planetary gear device is a great choice if your planetary motor’s speed is high. A high-quality planetary gear system can provide a superior performance than conventional systems.
A planetary gear system is a complex mechanism, involving three moving links that are connected to each other through joints. The sun gear acts as an input and the planet gears act as outputs. They rotate about their axes at a ratio determined by the number of teeth on each gear. The sun gear has 24 teeth, while the planet gears have three-quarters that ratio. This ratio makes a planetary motor extremely efficient.

planetary gear train

To predict the free vibration response of a planetary motor gear train, it is essential to develop a mathematical model for the system. Previously, static and dynamic models were used to study the behavior of planetary motor gear trains. In this study, a dynamic model was developed to investigate the effects of key design parameters on the vibratory response. Key parameters for planetary gear transmissions include the structure stiffness and mesh stiffness, and the mass and location of the shaft and bearing supports.
The design of the planetary motor gear train consists of several stages that can run with variable input speeds. The design of the gear train enables the transmission of high torques by dividing the load across multiple planetary gears. In addition, the planetary gear train has multiple teeth which mesh simultaneously in operation. This design also allows for higher efficiency and transmittable torque. Here are some other advantages of planetary motor gear trains. All these advantages make planetary motor gear trains one of the most popular types of planetary motors.
The compact footprint of planetary gears allows for excellent heat dissipation. High speeds and sustained performances will require lubrication. This lubricant can also reduce noise and vibration. But if these characteristics are not desirable for your application, you can choose a different gear type. Alternatively, if you want to maintain high performance, a planetary motor gear train will be the best choice. So, what are the advantages of planetary motor gears?

planetary gear train with fixed carrier train ratio

The planetary gear train is a common type of transmission in various machines. Its main advantages are high efficiency, compactness, large transmission ratio, and power-to-weight ratio. This type of gear train is a combination of spur gears, single-helical gears, and herringbone gears. Herringbone planetary gears have lower axial force and high load carrying capacity. Herringbone planetary gears are commonly used in heavy machinery and transmissions of large vehicles.
To use a planetary gear train with a fixed carrier train ratio, the first and second planets must be in a carrier position. The first planet is rotated so that its teeth mesh with the sun’s. The second planet, however, cannot rotate. It must be in a carrier position so that it can mesh with the sun. This requires a high degree of precision, so the planetary gear train is usually made of multiple sets. A little analysis will simplify this design.
The planetary gear train is made up of three components. The outer ring gear is supported by a ring gear. Each gear is positioned at a specific angle relative to one another. This allows the gears to rotate at a fixed rate while transferring the motion. This design is also popular in bicycles and other small vehicles. If the planetary gear train has several stages, multiple ring gears may be shared. A stationary ring gear is also used in pencil sharpener mechanisms. Planet gears are extended into cylindrical cutters. The ring gear is stationary and the planet gears rotate around a sun axis. In the case of this design, the outer ring gear will have a -3/2 planet gear ratio.
Motor

planetary gear train with zero helix angle

The torque distribution in a planetary gear is skewed, and this will drastically reduce the load carrying capacity of a needle bearing, and therefore the life of the bearing. To better understand how this can affect a gear train, we will examine two studies conducted on the load distribution of a planetary gear with a zero helix angle. The first study was done with a highly specialized program from the bearing manufacturer INA/FAG. The red line represents the load distribution along a needle roller in a zero helix gear, while the green line corresponds to the same distribution of loads in a 15 degree helix angle gear.
Another method for determining a gear’s helix angle is to consider the ratio of the sun and planet gears. While the sun gear is normally on the input side, the planet gears are on the output side. The sun gear is stationary. The two gears are in engagement with a ring gear that rotates 45 degrees clockwise. Both gears are attached to pins that support the planet gears. In the figure below, you can see the tangential and axial gear mesh forces on a planetary gear train.
Another method used for calculating power loss in a planetary gear train is the use of an auto transmission. This type of gear provides balanced performance in both power efficiency and load capacity. Despite the complexities, this method provides a more accurate analysis of how the helix angle affects power loss in a planetary gear train. If you’re interested in reducing the power loss of a planetary gear train, read on!

planetary gear train with spur gears

A planetary gearset is a type of mechanical drive system that uses spur gears that move in opposite directions within a plane. Spur gears are one of the more basic types of gears, as they don’t require any specialty cuts or angles to work. Instead, spur gears use a complex tooth shape to determine where the teeth will make contact. This in turn, will determine the amount of power, torque, and speed they can produce.
A two-stage planetary gear train with spur gears is also possible to run at variable input speeds. For such a setup, a mathematical model of the gear train is developed. Simulation of the dynamic behaviour highlights the non-stationary effects, and the results are in good agreement with the experimental data. As the ratio of spur gears to spur gears is not constant, it is called a dedendum.
A planetary gear train with spur gears is a type of epicyclic gear train. In this case, spur gears run between gears that contain both internal and external teeth. The circumferential motion of the spur gears is analogous to the rotation of planets in the solar system. There are four main components of a planetary gear train. The planet gear is positioned inside the sun gear and rotates to transfer motion to the sun gear. The planet gears are mounted on a joint carrier that is connected to the output shaft.
Motor

planetary gear train with helical gears

A planetary gear train with helical teeth is an extremely powerful transmission system that can provide high levels of power density. Helical gears are used to increase efficiency by providing a more efficient alternative to conventional worm gears. This type of transmission has the potential to improve the overall performance of a system, and its benefits extend far beyond the power density. But what makes this transmission system so appealing? What are the key factors to consider when designing this type of transmission system?
The most basic planetary train consists of the sun gear, planet gear, and ring gear elements. The number of planets varies, but the basic structure of planetary gears is similar. A simple planetary geartrain has the sun gear driving a carrier assembly. The number of planets can be as low as two or as high as six. A planetary gear train has a low mass inertia and is compact and reliable.
The mesh phase properties of a planetary gear train are particularly important in designing the profiles. Various parameters such as mesh phase difference and tooth profile modifications must be studied in depth in order to fully understand the dynamic characteristics of a PGT. These factors, together with others, determine the helical gears’ performance. It is therefore essential to understand the mesh phase of a planetary gear train to design it effectively.

China high quality 45mm 12V High Torque Low Speed Planetary Gear Motor   with Good qualityChina high quality 45mm 12V High Torque Low Speed Planetary Gear Motor   with Good quality
editor by CX 2023-05-29

China 24V 48V Low Speed High Torque DC Motor DC Planetary Gear Motor High Torque DC Motor with Planetary Gearbox Gear Ratio: 1: 36 motor efficiency

Product Description

Product Features

 A DC Motor whose poles are made of Permanent Magnets is known as Permanent Magnet DC (PMDC) Motor. The magnets are radially magnetized and are mounted on the inner periphery of the cylindrical steel stator. The stator of the motor serves as  a return path for the magnetic flux. The rotor has a DC armature, with commutator segments and brushes.

Applications of the Permanent Magnet DC Motor

The PMDC motors are used in various applications ranging from fractions to several horsepower.  They are developed up to about 200 kW for use in various industries. The following applications are given below.

PMDC motors are mainly used in automobiles to operate windshield wipers and washers, to raise the lower windows, to drive blowers for heaters and air conditioners etc.

They are also used in computer drives.high torque dc planetary gear motor

These types of motors are also used in toy industries.

PMDC motors are used in electric toothbrushes, portable vacuum cleaners, food mixers.dc high torque geared motor

Used in a portable electric tool such as drilling machines, hedge trimmers etc.

Advantages of the Permanent Magnet DC Motor

Following are the advantages of the PMDC Motor.

They are smaller in size.24v dc motor low rpm

For smaller rating Permanent Magnet reduces the manufacturing cost and thus PMDC motor are cheaper.

As these motors do not require field windings, they do not have field circuit copper losses. This increases their efficiency.
 

Model (mN.m)Torque (r/min)Speed 1Power (V)Voltage (A)Current ≤ (r/min)Speed tolerance
55ZYT01 63.7 3000 20 24 1.5 200
55ZYT02 63.7 3000 20 27 1.3 200
55ZYT03 63.7 3000 20 48 0.7 200
55ZYT04 63.7 3000 20 110 0.34 200
552YT05 55.7 6000 35 24 2.5 300
55ZYT06 55.7 6000 35 27 2.2 300
55ZYT07 55.7 6000 35 48 1.3 300
55ZYT08 55.7 6000 35 110 0.54 300
55ZYT09 78 2500 20.4 12 3.2 150
55ZYT10 63.7 3600 24 110 0.4 200
55ZYT51 92.3 3000 29 24 1.7 200
55ZYT52 92.3 3000 29 27 1.8 200
55ZYT53 92.3 3000 29 48 1.1 200
55ZYT54 92.3 3000 29 110 0.46 200
55ZYT55 79.6 6000 50 24 3.45 300
55ZYT56 79.6 6000 50 27 3.1 300
55ZYT57 79.6 6000 50 48 1.74 300
55ZYT58 79.6 6000 50 110 0.74 300
55ZYT59 92.3 1500 15 12 1.7 200
55ZYT60 79.6 3000 29 12 3.45 300
55ZYT61 76.4 5000 40 24 2.5 250
55ZYT63 127.4 1500 20 24 1.25 100
55ZYT64 95 3000 30 220 0.25 200
55ZYT65 89.2 7500 70 110 1.0 400
552YT66 110.8 2500 29 110 0.45 150
55ZYT68 69.6 5500 40 36 1.7 250
55ZYT72 95.5 2500 25 24 1.7 150
55ZYT76 92.3 2000 19 110 0.27 100
55ZYT105 108.2 7500 85 110 1.2 400
Model (mN.m)Torque (r/min)Speed 1Power (V)Voltage (A)Current ≤ (r/min)Speed tolerance
70ZYT01 159.2 3000 50 24 3.2 200
70ZYT02 159.2 3000 50 27 2.9 200
70ZYT03 159.2 3000 50 48 1.5 200
10ZYT04 159.2 3000 50 110 0.7 200
70ZYT05 135.4 6000 85 24 5.2 300
70ZYT06 135.4 6000 85 27 4.8 300
70ZYT07 135.4 6000 85 48 2.6 300
70ZYT08 135.4 6000 85 110 1.1 300
70ZYT13 151.9 2200 35 90 0.6 150
70ZYT14 152.9 2500 40 180 0.35 150
70ZYT16 191 2000 40 24 2.3 100
70ZYT21 95.5 3000 30 220 0.2 200
70ZYT51 223 3000 70 24 4.3 200
70ZYT52 223 3000 70 27 3.8 200
70ZYT53 223 3000 70 48 2.2 200
70ZYT54 223 3000 70 110 0.95 200
70ZYT55 191.1 6000 120 24 7.5 300
70ZYT56 191.1 6000 120 27 6.6 300
70ZYT57 191.1 6000 120 48 3.8 300
70ZYT58 191.1 6000 120 220 0.8 300
70ZYT59 223 1500 35 12 4.3 200
70ZYT60 238.8 4000 100 110 1.3 200
70ZYT61 191.1 6000 120 90 1.8 300
70ZYT76 191.1 2500 50 24 3 150
70ZYT77 318.5 1500 50 48 1.6 100
Model (mN.m)Torque (r/min)Speed 1Power (V)Voltage (A)Current ≤ (r/min)Speed tolerance
90ZYT01 323 1500 50 110 0.66 100
90ZYT02 323 1500 50 220 0.33 100
90ZYT03 294 3000 92 110 1.2 200
90ZYT04 294 3000 92 220 0.6 200
9OZYTO5 294 3000 92 24 6.1 200
90ZYT51 510 1500 80 110 1.1 100
90ZYT52 510 1500 80 220 0.55 100
90ZYT53 480 3000 150 110 2.0 200
90ZYT54 480 3000 150 220 1.0 200
90ZYT55 510 1500 80 12/24 10/5.0 100
9OZYT101 796 1500 125 110 1.6 100
90ZYT102 796 1500 125 220 0.8 100
90ZYT103 733 3000 230 110 2.8 200
9OZYT104 733 3000 230 220 1.5 200
9OZYT105 733 3000 230 24 13.5 200
90ZYT106 733 1500 125 12/24 13/6.5 100
90ZYT107 733 1300 100 36 4 100
9OZYT108 733 3000 250 48 6.5 200
Model (mN.m)Torque (r/min)Speed 1Power (V)Voltage (A)Current ≤ (r/min)Speed tolerance
110ZYT01 784 1500 123 110 1.8 100
110ZYT02 784 1500 123 220 0.9 100
110ZYT03 637 3000 200 110 2.8 200
110ZYT04 637 3000 200 220 1.4 200
110ZYT05 637 3000 200 24 13 200
110ZYT51 1177 1500 185 110 2.5 100
110ZYT52 1177 1500 185 220 1.25 100
110ZYT53 980 3000 308 110 4.0 200
110ZYT54 980 3000 308 220 2.0 200
110ZYT55 980 3000 308 24 16.5 200
110ZYT101 1560 1500 245 110 3.0 100
110ZYT102 1560 1500 245 220 1.5 100
110ZYT103 1274 3000 400 110 4.8 200
110ZYT104 1274 3000 400 220 2.4 200
110ZYT105 1274 3000 400 24 22.5 200
110ZYT106 1274 1500 245 12/24 24/12 100
110ZYT151 2390 1500 375 110 4.5 100
110ZYT152 2390 1500 375 220 2.3 100
110ZYT153 2230 3000 700 110 8.5 200
110ZYT154 2230 3000 700 220 4.2 200
110ZYT155 2230 3000 700 24 45 200
110ZYT156 2230 1500 375 12/24 44/22 100
Model (mN.m)Torque (r/min)Speed 1Power (V)Voltage (A)Current ≤ (r/min)Speed tolerance
1302YT01 2548 1500 400 110 4.8 100
130ZYT02 2548 1500 400 220 2.4 100
130ZYT03 2548 3000 800 110 9 200
130ZYT04 2548 3000 800 220 4.5 200
130ZYT05 3185 1500 500 24 28 100
130ZYT51 3185 1500 500 110 5.8 100
130ZYT52 3185 1500 500 220 2.9 100
130ZYT53 3185 3000 1000 110 11 200
130ZYT54 3185 3000 1000 220 5.5 200
130ZYT55 3185 3000 1000 24 50 200
130ZYT56 3185 1500 500 24 25 100
130ZYT101 3822 1500 600 110 7 01
130ZYT102 3822 1500 600 220 3.5 100
130ZYT103 3822 3000 1200 110 13 200
130ZYT104 3822 3000 1200 220 6.5 200
130ZYT105 3822 3000 1200 24 55 200
130ZYT106 3822 1500 600 24 30 100
130ZYT156 4775 1500 750 24 35 100
130ZYT157 4775 3000 1500 24 70 100
130ZYT158 6366 1500 1000 24 50 200

        Motor production workshop and equipment

Shipping & Packaging

 

US $130
/ Piece
|
1 Piece

(Min. Order)

###

Shipping Cost:

Estimated freight per unit.



To be negotiated

###

Application: Universal, Industrial, Household Appliances, Car, Power Tools
Operating Speed: Adjust Speed
Function: Driving

###

Model (mN.m)Torque (r/min)Speed 1Power (V)Voltage (A)Current ≤ (r/min)Speed tolerance
55ZYT01 63.7 3000 20 24 1.5 200
55ZYT02 63.7 3000 20 27 1.3 200
55ZYT03 63.7 3000 20 48 0.7 200
55ZYT04 63.7 3000 20 110 0.34 200
552YT05 55.7 6000 35 24 2.5 300
55ZYT06 55.7 6000 35 27 2.2 300
55ZYT07 55.7 6000 35 48 1.3 300
55ZYT08 55.7 6000 35 110 0.54 300
55ZYT09 78 2500 20.4 12 3.2 150
55ZYT10 63.7 3600 24 110 0.4 200
55ZYT51 92.3 3000 29 24 1.7 200
55ZYT52 92.3 3000 29 27 1.8 200
55ZYT53 92.3 3000 29 48 1.1 200
55ZYT54 92.3 3000 29 110 0.46 200
55ZYT55 79.6 6000 50 24 3.45 300
55ZYT56 79.6 6000 50 27 3.1 300
55ZYT57 79.6 6000 50 48 1.74 300
55ZYT58 79.6 6000 50 110 0.74 300
55ZYT59 92.3 1500 15 12 1.7 200
55ZYT60 79.6 3000 29 12 3.45 300
55ZYT61 76.4 5000 40 24 2.5 250
55ZYT63 127.4 1500 20 24 1.25 100
55ZYT64 95 3000 30 220 0.25 200
55ZYT65 89.2 7500 70 110 1.0 400
552YT66 110.8 2500 29 110 0.45 150
55ZYT68 69.6 5500 40 36 1.7 250
55ZYT72 95.5 2500 25 24 1.7 150
55ZYT76 92.3 2000 19 110 0.27 100
55ZYT105 108.2 7500 85 110 1.2 400
Model (mN.m)Torque (r/min)Speed 1Power (V)Voltage (A)Current ≤ (r/min)Speed tolerance
70ZYT01 159.2 3000 50 24 3.2 200
70ZYT02 159.2 3000 50 27 2.9 200
70ZYT03 159.2 3000 50 48 1.5 200
10ZYT04 159.2 3000 50 110 0.7 200
70ZYT05 135.4 6000 85 24 5.2 300
70ZYT06 135.4 6000 85 27 4.8 300
70ZYT07 135.4 6000 85 48 2.6 300
70ZYT08 135.4 6000 85 110 1.1 300
70ZYT13 151.9 2200 35 90 0.6 150
70ZYT14 152.9 2500 40 180 0.35 150
70ZYT16 191 2000 40 24 2.3 100
70ZYT21 95.5 3000 30 220 0.2 200
70ZYT51 223 3000 70 24 4.3 200
70ZYT52 223 3000 70 27 3.8 200
70ZYT53 223 3000 70 48 2.2 200
70ZYT54 223 3000 70 110 0.95 200
70ZYT55 191.1 6000 120 24 7.5 300
70ZYT56 191.1 6000 120 27 6.6 300
70ZYT57 191.1 6000 120 48 3.8 300
70ZYT58 191.1 6000 120 220 0.8 300
70ZYT59 223 1500 35 12 4.3 200
70ZYT60 238.8 4000 100 110 1.3 200
70ZYT61 191.1 6000 120 90 1.8 300
70ZYT76 191.1 2500 50 24 3 150
70ZYT77 318.5 1500 50 48 1.6 100
Model (mN.m)Torque (r/min)Speed 1Power (V)Voltage (A)Current ≤ (r/min)Speed tolerance
90ZYT01 323 1500 50 110 0.66 100
90ZYT02 323 1500 50 220 0.33 100
90ZYT03 294 3000 92 110 1.2 200
90ZYT04 294 3000 92 220 0.6 200
9OZYTO5 294 3000 92 24 6.1 200
90ZYT51 510 1500 80 110 1.1 100
90ZYT52 510 1500 80 220 0.55 100
90ZYT53 480 3000 150 110 2.0 200
90ZYT54 480 3000 150 220 1.0 200
90ZYT55 510 1500 80 12/24 10/5.0 100
9OZYT101 796 1500 125 110 1.6 100
90ZYT102 796 1500 125 220 0.8 100
90ZYT103 733 3000 230 110 2.8 200
9OZYT104 733 3000 230 220 1.5 200
9OZYT105 733 3000 230 24 13.5 200
90ZYT106 733 1500 125 12/24 13/6.5 100
90ZYT107 733 1300 100 36 4 100
9OZYT108 733 3000 250 48 6.5 200
Model (mN.m)Torque (r/min)Speed 1Power (V)Voltage (A)Current ≤ (r/min)Speed tolerance
110ZYT01 784 1500 123 110 1.8 100
110ZYT02 784 1500 123 220 0.9 100
110ZYT03 637 3000 200 110 2.8 200
110ZYT04 637 3000 200 220 1.4 200
110ZYT05 637 3000 200 24 13 200
110ZYT51 1177 1500 185 110 2.5 100
110ZYT52 1177 1500 185 220 1.25 100
110ZYT53 980 3000 308 110 4.0 200
110ZYT54 980 3000 308 220 2.0 200
110ZYT55 980 3000 308 24 16.5 200
110ZYT101 1560 1500 245 110 3.0 100
110ZYT102 1560 1500 245 220 1.5 100
110ZYT103 1274 3000 400 110 4.8 200
110ZYT104 1274 3000 400 220 2.4 200
110ZYT105 1274 3000 400 24 22.5 200
110ZYT106 1274 1500 245 12/24 24/12 100
110ZYT151 2390 1500 375 110 4.5 100
110ZYT152 2390 1500 375 220 2.3 100
110ZYT153 2230 3000 700 110 8.5 200
110ZYT154 2230 3000 700 220 4.2 200
110ZYT155 2230 3000 700 24 45 200
110ZYT156 2230 1500 375 12/24 44/22 100
Model (mN.m)Torque (r/min)Speed 1Power (V)Voltage (A)Current ≤ (r/min)Speed tolerance
1302YT01 2548 1500 400 110 4.8 100
130ZYT02 2548 1500 400 220 2.4 100
130ZYT03 2548 3000 800 110 9 200
130ZYT04 2548 3000 800 220 4.5 200
130ZYT05 3185 1500 500 24 28 100
130ZYT51 3185 1500 500 110 5.8 100
130ZYT52 3185 1500 500 220 2.9 100
130ZYT53 3185 3000 1000 110 11 200
130ZYT54 3185 3000 1000 220 5.5 200
130ZYT55 3185 3000 1000 24 50 200
130ZYT56 3185 1500 500 24 25 100
130ZYT101 3822 1500 600 110 7 01
130ZYT102 3822 1500 600 220 3.5 100
130ZYT103 3822 3000 1200 110 13 200
130ZYT104 3822 3000 1200 220 6.5 200
130ZYT105 3822 3000 1200 24 55 200
130ZYT106 3822 1500 600 24 30 100
130ZYT156 4775 1500 750 24 35 100
130ZYT157 4775 3000 1500 24 70 100
130ZYT158 6366 1500 1000 24 50 200
US $130
/ Piece
|
1 Piece

(Min. Order)

###

Shipping Cost:

Estimated freight per unit.



To be negotiated

###

Application: Universal, Industrial, Household Appliances, Car, Power Tools
Operating Speed: Adjust Speed
Function: Driving

###

Model (mN.m)Torque (r/min)Speed 1Power (V)Voltage (A)Current ≤ (r/min)Speed tolerance
55ZYT01 63.7 3000 20 24 1.5 200
55ZYT02 63.7 3000 20 27 1.3 200
55ZYT03 63.7 3000 20 48 0.7 200
55ZYT04 63.7 3000 20 110 0.34 200
552YT05 55.7 6000 35 24 2.5 300
55ZYT06 55.7 6000 35 27 2.2 300
55ZYT07 55.7 6000 35 48 1.3 300
55ZYT08 55.7 6000 35 110 0.54 300
55ZYT09 78 2500 20.4 12 3.2 150
55ZYT10 63.7 3600 24 110 0.4 200
55ZYT51 92.3 3000 29 24 1.7 200
55ZYT52 92.3 3000 29 27 1.8 200
55ZYT53 92.3 3000 29 48 1.1 200
55ZYT54 92.3 3000 29 110 0.46 200
55ZYT55 79.6 6000 50 24 3.45 300
55ZYT56 79.6 6000 50 27 3.1 300
55ZYT57 79.6 6000 50 48 1.74 300
55ZYT58 79.6 6000 50 110 0.74 300
55ZYT59 92.3 1500 15 12 1.7 200
55ZYT60 79.6 3000 29 12 3.45 300
55ZYT61 76.4 5000 40 24 2.5 250
55ZYT63 127.4 1500 20 24 1.25 100
55ZYT64 95 3000 30 220 0.25 200
55ZYT65 89.2 7500 70 110 1.0 400
552YT66 110.8 2500 29 110 0.45 150
55ZYT68 69.6 5500 40 36 1.7 250
55ZYT72 95.5 2500 25 24 1.7 150
55ZYT76 92.3 2000 19 110 0.27 100
55ZYT105 108.2 7500 85 110 1.2 400
Model (mN.m)Torque (r/min)Speed 1Power (V)Voltage (A)Current ≤ (r/min)Speed tolerance
70ZYT01 159.2 3000 50 24 3.2 200
70ZYT02 159.2 3000 50 27 2.9 200
70ZYT03 159.2 3000 50 48 1.5 200
10ZYT04 159.2 3000 50 110 0.7 200
70ZYT05 135.4 6000 85 24 5.2 300
70ZYT06 135.4 6000 85 27 4.8 300
70ZYT07 135.4 6000 85 48 2.6 300
70ZYT08 135.4 6000 85 110 1.1 300
70ZYT13 151.9 2200 35 90 0.6 150
70ZYT14 152.9 2500 40 180 0.35 150
70ZYT16 191 2000 40 24 2.3 100
70ZYT21 95.5 3000 30 220 0.2 200
70ZYT51 223 3000 70 24 4.3 200
70ZYT52 223 3000 70 27 3.8 200
70ZYT53 223 3000 70 48 2.2 200
70ZYT54 223 3000 70 110 0.95 200
70ZYT55 191.1 6000 120 24 7.5 300
70ZYT56 191.1 6000 120 27 6.6 300
70ZYT57 191.1 6000 120 48 3.8 300
70ZYT58 191.1 6000 120 220 0.8 300
70ZYT59 223 1500 35 12 4.3 200
70ZYT60 238.8 4000 100 110 1.3 200
70ZYT61 191.1 6000 120 90 1.8 300
70ZYT76 191.1 2500 50 24 3 150
70ZYT77 318.5 1500 50 48 1.6 100
Model (mN.m)Torque (r/min)Speed 1Power (V)Voltage (A)Current ≤ (r/min)Speed tolerance
90ZYT01 323 1500 50 110 0.66 100
90ZYT02 323 1500 50 220 0.33 100
90ZYT03 294 3000 92 110 1.2 200
90ZYT04 294 3000 92 220 0.6 200
9OZYTO5 294 3000 92 24 6.1 200
90ZYT51 510 1500 80 110 1.1 100
90ZYT52 510 1500 80 220 0.55 100
90ZYT53 480 3000 150 110 2.0 200
90ZYT54 480 3000 150 220 1.0 200
90ZYT55 510 1500 80 12/24 10/5.0 100
9OZYT101 796 1500 125 110 1.6 100
90ZYT102 796 1500 125 220 0.8 100
90ZYT103 733 3000 230 110 2.8 200
9OZYT104 733 3000 230 220 1.5 200
9OZYT105 733 3000 230 24 13.5 200
90ZYT106 733 1500 125 12/24 13/6.5 100
90ZYT107 733 1300 100 36 4 100
9OZYT108 733 3000 250 48 6.5 200
Model (mN.m)Torque (r/min)Speed 1Power (V)Voltage (A)Current ≤ (r/min)Speed tolerance
110ZYT01 784 1500 123 110 1.8 100
110ZYT02 784 1500 123 220 0.9 100
110ZYT03 637 3000 200 110 2.8 200
110ZYT04 637 3000 200 220 1.4 200
110ZYT05 637 3000 200 24 13 200
110ZYT51 1177 1500 185 110 2.5 100
110ZYT52 1177 1500 185 220 1.25 100
110ZYT53 980 3000 308 110 4.0 200
110ZYT54 980 3000 308 220 2.0 200
110ZYT55 980 3000 308 24 16.5 200
110ZYT101 1560 1500 245 110 3.0 100
110ZYT102 1560 1500 245 220 1.5 100
110ZYT103 1274 3000 400 110 4.8 200
110ZYT104 1274 3000 400 220 2.4 200
110ZYT105 1274 3000 400 24 22.5 200
110ZYT106 1274 1500 245 12/24 24/12 100
110ZYT151 2390 1500 375 110 4.5 100
110ZYT152 2390 1500 375 220 2.3 100
110ZYT153 2230 3000 700 110 8.5 200
110ZYT154 2230 3000 700 220 4.2 200
110ZYT155 2230 3000 700 24 45 200
110ZYT156 2230 1500 375 12/24 44/22 100
Model (mN.m)Torque (r/min)Speed 1Power (V)Voltage (A)Current ≤ (r/min)Speed tolerance
1302YT01 2548 1500 400 110 4.8 100
130ZYT02 2548 1500 400 220 2.4 100
130ZYT03 2548 3000 800 110 9 200
130ZYT04 2548 3000 800 220 4.5 200
130ZYT05 3185 1500 500 24 28 100
130ZYT51 3185 1500 500 110 5.8 100
130ZYT52 3185 1500 500 220 2.9 100
130ZYT53 3185 3000 1000 110 11 200
130ZYT54 3185 3000 1000 220 5.5 200
130ZYT55 3185 3000 1000 24 50 200
130ZYT56 3185 1500 500 24 25 100
130ZYT101 3822 1500 600 110 7 01
130ZYT102 3822 1500 600 220 3.5 100
130ZYT103 3822 3000 1200 110 13 200
130ZYT104 3822 3000 1200 220 6.5 200
130ZYT105 3822 3000 1200 24 55 200
130ZYT106 3822 1500 600 24 30 100
130ZYT156 4775 1500 750 24 35 100
130ZYT157 4775 3000 1500 24 70 100
130ZYT158 6366 1500 1000 24 50 200

How to Assemble a Planetary Motor

A Planetary Motor uses multiple planetary surfaces to produce torque and rotational speed. The planetary system allows for a wide range of gear reductions. Planetary systems are particularly effective in applications where higher torques and torque density are needed. As such, they are a popular choice for electric vehicles and other applications where high-speed mobility is required. Nevertheless, there are many benefits associated with using a planetary motor. Read on to learn more about these motors.

VPLite

If you’re looking to replace the original VP, the VPLite has a similar output shaft as the original. This means that you can mix and match your original gear sets, including the input and output shafts. You can even mix metal inputs with plastic outputs. Moreover, if you decide to replace the gearbox, you can easily disassemble the entire unit and replace it with a new one without losing any output torque.
Compared to a planetary motor, a spur gear motor uses fewer gears and is therefore cheaper to produce. However, the latter isn’t suitable for high-torque applications. The torque produced by a planetary gearmotor is evenly distributed, which makes it ideal for applications that require higher torque. However, you may have to compromise on the torque output if you’re looking for a lightweight option.
The VersaPlanetary Lite gearbox replaces the aluminum ring gear with a 30% glass-filled nylon gear. This gearbox is available in two sizes, which means you can mix and match parts to get a better gear ratio. The VPLite gearbox also has a female 5mm hex output shaft. You can mix and match different gearboxes and planetary gearboxes for maximum efficiency.
Motor

VersaPlanetary

The VersaPlanetary is a highly versatile planetary motor that can be mounted in a variety of ways. Its unique design includes a removable shaft coupler system that makes it simple to swap out the motor with another. This planetary motor mounts in any position where a CIM motor mounts. Here’s how to assemble the motor. First, remove the hex output shaft from the VersaPlanetary output stage. Its single ring clip holds it in place. You can use a drill press to drill a hole into the output shaft.
After mounting the gearbox, you can then mount the motor. The mounting hardware included with the VersaPlanetary Planetary Motor comes with four 10-32 threaded holes on a two-inch bolt circle. You can use these holes to mount your VersaPlanetary on a CIM motor or a CIM-compatible motor. Once assembled, the VersaPlanetary gearbox has 72 different gear ratios.
The VersaPlanetary gearbox is interchangeable with regular planetary gearboxes. However, it does require additional parts. You can purchase a gearbox without the motor but you’ll need a pinion. The pinion attaches to the shaft of the motor. The gearbox is very sturdy and durable, so you won’t have to worry about it breaking or wearing out.

Self-centering planetary gears

A planetary motor is a simple mechanical device that rotates around a axis, with the planets moving around the shaft in a radial direction. The planets are positioned so that they mesh with both the sun gear and the output gears. The carrier 48 is flexibly connected to the drive shaft and can move depending on the forces exerted by the planet gears. In this way, the planets can always be in the optimal mesh with the output gears and sun gear.
The first step in developing a planetary gear motor is to identify the number of teeth in each planet. The number of teeth should be an integer. The tooth diameters of the planets should mesh with each other and the ring. Typically, the teeth of one planet must mesh with each other, but the spacing between them must be equal or greater than the other. This can be achieved by considering the tooth count of each planet, as well as the spacing between planets.
A second step is to align the planet gears with the output gears. In a planetary motor, self-centering planetary gears must be aligned with both input and output gears to provide maximum torque. For this to be possible, the planet gears must be connected with the output shaft and the input shaft. Similarly, the output shaft should also be able to align with the input gear.
Motor

Encoders

A planetary geared motor is a DC motor with a planetary gearbox. The motor can be used to drive heavy loads and has a ratio of 104:1. The shaft speed is 116rpm when it is unloaded. A planetary gearbox has a low backlash and is often used in applications that need high torque. Planetary Motor encoders can help you keep track of your robot’s position or speed.
They are also able to control motor position and speed with precision. Most of them feature high resolution. A 0.18-degree resolution encoder will give you a minimum of 2000 transitions per rotation between outputs A and B. The encoder is built to industrial standards and has a sturdy gearbox to avoid damage. The encoder’s robust design means it will not stall when the motor reaches its maximum speed.
There are many advantages to a planetary motor encoder. A high-quality one will not lose its position or speed even if it’s subject to shocks. A good quality planetary motor will also last a long time. Planetary motors are great for resale or for your own project. If you’re considering buying a planetary motor, consider this information. It’ll help you decide if a particular model is right for your needs.

Cost

There are several advantages of planetary motors. One of the biggest is their cost, but they can also be used in many different applications. They can be combined with a variety of gearboxes, and are ideal for various types of robots, laboratory automation, and production applications. Planetary gearboxes are available in many different materials, and plastic planetary gearboxes are an economical alternative. Plastic gearboxes reduce noise at higher speeds, and steel input stage gears are available for high torques. A modified lubrication system can help with difficult operating conditions.
In addition to being more durable, planetary motors are much more efficient. They use fewer gears, which lowers the overall cost of production. Depending on the application, a planetary motor can be used to move a heavy object, but is generally less expensive than its counterpart. It is a better choice for situations where the load is relatively low and the motor is not used frequently. If you need a very high torque output, a planetary motor may be the better option.
Planetary gear units are a good choice for applications requiring high precision, high dynamics, and high torque density. They can be designed and built using TwinCAT and TC Motion Designer, and are delivered as complete motor and gear unit assemblies. In a few simple steps, you can calculate the torque required and compare the costs of different planetary gear units. You can then choose the best model for your application. And because planetary gear units are so efficient, they are a great option for high-end industrial applications.
Motor

Applications

There are several different applications of the planetary motor. One such application is in motion control. Planetary gearboxes have many benefits, including high torque, low backlash, and torsional stiffness. They also have an extremely compact design, and can be used for a variety of applications, from rack and pinion drives to delta robotics. In many cases, they are less expensive to manufacture and use than other types of motors.
Another application for planetary gear units is in rotary tables. These machines require high precision and low backlash for their precise positioning. Planetary gears are also necessary for noise reduction, which is a common feature in rotary tables. High precision planetary gears can make the height adjustment of OP tables a breeze. And because they are extremely durable and require low noise, they are a great choice for this application. In this case, the planetary gear is matched with an AM8000 series servomotor, which gives a wide range of choices.
The planetary gear transmission is also widely used in helicopters, automobiles, and marine applications. It is more advanced than a countershaft drive, and is capable of higher torque to weight ratios. Other advantages include its compact design and reduced noise. A key concern in the development of this type of transmission is to minimize vibration. If the output of a planetary gear transmission system is loud, the vibration caused by this type of drive system may be too loud for comfort.

China 24V 48V Low Speed High Torque DC Motor DC Planetary Gear Motor High Torque DC Motor with Planetary Gearbox Gear Ratio: 1: 36     motor efficiencyChina 24V 48V Low Speed High Torque DC Motor DC Planetary Gear Motor High Torque DC Motor with Planetary Gearbox Gear Ratio: 1: 36     motor efficiency
editor by czh 2022-11-26

China 24V Round Flange High Torque Low Speed Planetary Gearbox Gear DC Motor with Great quality

Product Description

Product Description

Brushless Gear Motor 
1. High efficiency and energy saving.

2. Speed reduction ratio is optional.

3.The external scheme can be used in bulk sorting and transportation.

4.The drum motor is customized for the conveying line.

5.With brushless gear motor, 50 kg load can be easily driven.

6.Integrated photoelectric input and output ports, easier field wiring.

7.15 internal rotating speeds and 7 external rotating speeds.

Product Parameters

 

Detailed Photos

 

 

More Models

 

Packaging & Shipping

 

 

Certifications

 

FAQ

 

Q: How to order?
A: send us inquiry → receive our quotation → negotiate details → confirm the sample → sign contract/deposit → mass production → cargo ready → balance/delivery → further cooperation.

Q: How about Sample order?
A: Sample is available for you. please contact us for details. Contact us

Q: Which shipping way is avaliable?
A: DHL, UPS, FedEx, TNT, EMS, China Post,Sea are available.The other shipping ways are also available, please contact us if you need ship by the other shipping way. 

Q: How long is the deliver?
A: Devliver time depends on the quantity you order. usually it takes 15-25 working days.

Q: My package has missing products. What can I do?
A: Please contact our support team and we will confirm your order with the package contents.We apologize for any inconveniences. 

Q: How to confirm the payment?
A: We accept payment by T/T, PayPal, the other payment ways also could be accepted,Please contact us before you pay by the other payment ways. Also 30-50% deposit is available, the balance money should be paid before shipping.
 

US $48-50
/ Piece
|
100 Pieces

(Min. Order)

###

Application: Car
Speed: Constant Speed
Number of Stator: Single-Phase
Function: Driving
Casing Protection: Totally Enclosed
Number of Poles: 4

###

Samples:
US$ 65/Piece
1 Piece(Min.Order)

|
Request Sample

###

Customization:
US $48-50
/ Piece
|
100 Pieces

(Min. Order)

###

Application: Car
Speed: Constant Speed
Number of Stator: Single-Phase
Function: Driving
Casing Protection: Totally Enclosed
Number of Poles: 4

###

Samples:
US$ 65/Piece
1 Piece(Min.Order)

|
Request Sample

###

Customization:

The Basics of a Planetary Motor

A Planetary Motor is a type of gearmotor that uses multiple planetary gears to deliver torque. This system minimizes the chances of failure of individual gears and increases output capacity. Compared to the planetary motor, the spur gear motor is less complex and less expensive. However, a spur gear motor is generally more suitable for applications requiring low torque. This is because each gear is responsible for the entire load, limiting its torque.

Self-centering planetary gears

This self-centering mechanism for a planetary motor is based on a helical arrangement. The helical structure involves a sun-planet, with its crown and slope modified. The gears are mounted on a ring and share the load evenly. The helical arrangement can be either self-centering or self-resonant. This method is suited for both applications.
A helical planetary gear transmission is illustrated in FIG. 1. A helical configuration includes an output shaft 18 and a sun gear 18. The drive shaft extends through an opening in the cover to engage drive pins on the planet carriers. The drive shaft of the planetary gears can be fixed to the helical arrangement or can be removable. The transmission system is symmetrical, allowing the output shaft of the planetary motor to rotate radially in response to the forces acting on the planet gears.
A flexible pin can improve load sharing. This modification may decrease the face load distribution, but increases the (K_Hbeta) parameter. This effect affects the gear rating and life. It is important to understand the effects of flexible pins. It is worth noting that there are several other disadvantages of flexible pins in helical PGSs. The benefits of flexible pins are discussed below.
Using self-centering planetary gears for a helical planetary motor is essential for symmetrical force distribution. These gears ensure the symmetry of force distribution. They can also be used for self-centering applications. Self-centering planetary gears also guarantee the proper force distribution. They are used to drive a planetary motor. The gearhead is made of a ring gear, and the output shaft is supported by two ball bearings. Self-centering planetary gears can handle a high torque input, and can be suited for many applications.
To solve for a planetary gear mechanism, you need to find its pitch curve. The first step is to find the radius of the internal gear ring. A noncircular planetary gear mechanism should be able to satisfy constraints that can be complex and nonlinear. Using a computer, you can solve for these constraints by analyzing the profile of the planetary wheel’s tooth curve.
Motor

High torque

Compared to the conventional planetary motors, high-torque planetary motors have a higher output torque and better transmission efficiency. The high-torque planetary motors are designed to withstand large loads and are used in many types of applications, such as medical equipment and miniature consumer electronics. Their compact design makes them suitable for small space-saving applications. In addition, these motors are designed for high-speed operation.
They come with a variety of shaft configurations and have a wide range of price-performance ratios. The FAULHABER planetary gearboxes are made of plastic, resulting in a good price-performance ratio. In addition, plastic input stage gears are used in applications requiring high torques, and steel input stage gears are available for higher speeds. For difficult operating conditions, modified lubrication is available.
Various planetary gear motors are available in different sizes and power levels. Generally, planetary gear motors are made of steel, brass, or plastic, though some use plastic for their gears. Steel-cut gears are the most durable, and are ideal for applications that require a high amount of torque. Similarly, nickel-steel gears are more lubricated and can withstand a high amount of wear.
The output torque of a high-torque planetary gearbox depends on its rated input speed. Industrial-grade high-torque planetary gearboxes are capable of up to 18000 RPM. Their output torque is not higher than 2000 nm. They are also used in machines where a planet is decelerating. Their working temperature ranges between 25 and 100 degrees Celsius. For best results, it is best to choose the right size for the application.
A high-torque planetary gearbox is the most suitable type of high-torque planetary motor. It is important to determine the deceleration ratio before buying one. If there is no product catalog that matches your servo motor, consider buying a close-fitting high-torque planetary gearbox. There are also high-torque planetary gearboxes available for custom-made applications.
Motor

High efficiency

A planetary gearbox is a type of mechanical device that is used for high-torque transmission. This gearbox is made of multiple pairs of gears. Large gears on the output shaft mesh with small gears on the input shaft. The ratio between the big and small gear teeth determines the transmittable torque. High-efficiency planetary gearheads are available for linear motion, axial loads, and sterilizable applications.
The AG2400 high-end gear unit series is ideally matched to Beckhoff’s extensive line of servomotors and gearboxes. Its single-stage and multi-stage transmission ratios are highly flexible and can be matched to different robot types. Its modified lubrication helps it operate in difficult operating conditions. These high-performance gear units are available in a wide range of sizes.
A planetary gear motor can be made of steel, nickel-steel, or brass. In addition to steel, some models use plastic. The planetary gears share work between multiple gears, making it easy to transfer high amounts of power without putting a lot of stress on the gears. The gears in a planetary gear motor are held together by a movable arm. High-efficiency planetary gear motors are more efficient than traditional gearmotors.
While a planetary gear motor can generate torque, it is more efficient and cheaper to produce. The planetary gear system is designed with all gears operating in synchrony, minimizing the chance of a single gear failure. The efficiency of a planetary gearmotor makes it a popular choice for high-torque applications. This type of motor is suitable for many applications, and is less expensive than a standard geared motor.
The planetary gearbox is a combination of a planetary type gearbox and a DC motor. The planetary gearbox is compact, versatile, and efficient, and can be used in a wide range of industrial environments. The planetary gearbox with an HN210 DC motor is used in a 22mm OD, PPH, and ph configuration with voltage operating between 6V and 24V. It is available in many configurations and can be custom-made to meet your application requirements.
Motor

High cost

In general, planetary gearmotors are more expensive than other configurations of gearmotors. This is due to the complexity of their design, which involves the use of a central sun gear and a set of planetary gears which mesh with each other. The entire assembly is enclosed in a larger internal tooth gear. However, planetary motors are more effective for higher load requirements. The cost of planetary motors varies depending on the number of gears and the number of planetary gears in the system.
If you want to build a planetary gearbox, you can purchase a gearbox for the motor. These gearboxes are often available with several ratios, and you can use any one to create a custom ratio. The cost of a gearbox depends on how much power you want to move with the gearbox, and how much gear ratio you need. You can even contact your local FRC team to purchase a gearbox for the motor.
Gearboxes play a major role in determining the efficiency of a planetary gearmotor. The output shafts used for this type of motor are usually made of steel or nickel-steel, while those used in planetary gearboxes are made from brass or plastic. The former is the most durable and is best for applications that require high torque. The latter, however, is more absorbent and is better at holding lubricant.
Using a planetary gearbox will allow you to reduce the input power required for the stepper motor. However, this is not without its downsides. A planetary gearbox can also be replaced with a spare part. A planetary gearbox is inexpensive, and its spare parts are inexpensive. A planetary gearbox has low cost compared to a planetary motor. Its advantages make it more desirable in certain applications.
Another advantage of a planetary gear unit is the ability to handle ultra-low speeds. Using a planetary gearbox allows stepper motors to avoid resonance zones, which can cause them to crawl. In addition, the planetary gear unit allows for safe and efficient cleaning. So, whether you’re considering a planetary gear unit for a particular application, these gear units can help you get exactly what you need.

China 24V Round Flange High Torque Low Speed Planetary Gearbox Gear DC Motor     with Great qualityChina 24V Round Flange High Torque Low Speed Planetary Gearbox Gear DC Motor     with Great quality
editor by czh 2022-11-25

China Best Sales Low Speed Electric 12/24/48V DC Gear Motor for Welding Machine Double Shaft near me shop

Product Description

eighteen.3V50W, 130RPM  Wire Feeder Motor
Dual/Double Output Shaft,  Brushed DC Push Motor,

Used For Wire Feeder,Feeding Device, Welding wire feeding device

  • Thin plate variety printed armature winding
  • Electrical power to quantity ratio
  • Broad speed assortment
  • Large linearity
  • Small instant of inertia
  • Huge output torque
  • Sleek procedure of the advantages

Specifications:

 Product types:  Brush Print DC Push Motor
 Model:  3DY-B
 Rated power:  50W
 Rated voltage:  18.3V
 Rated speed  130RPM
 Custom made:  Yes
Existing: 5.5A

Design Possibilities:

  1. Operating voltages to go well with
  2. Custom made shaft dimensions/profiles
  3. Tailored performance profiles
  4. Particular OEM configurations

Competitive Benefit:

*Light-weight excess weight, Small volume.

*Big commencing torque, Wide pace range.

*Reduced velocity procedure and excellent reversing performance.

*Effectively-designed creation engineering and the introduction of production line

Single-stage motors have a stator. They do not have the rotating magnetic area qualities of polyphase or polyphase motors. The magnetic discipline produced by the stator windings is pulsating, not rotating. When the rotor is stationary, the expansion and contraction of the stator’s magnetic field create an electrical present in the rotor. The recent generates the rotor magnetic discipline with the opposite polarity to the stator magnetic area. The reverse polarity applies rotational pressure to the higher and lower parts of the rotor. Because this force passes through the heart of the rotor, it stays equal in every single course, trying to keep the rotor stationary. If the rotor starts off to turn, it carries on to change in the route it commenced, since the rotor’s momentum results in a rotational power in that route. Solitary-phase motors are utilized in lower-electrical power applications such as ceiling followers, mixer grinders, and home appliances these kinds of as transportable electricity resources.
AC motors are also various from DC motors due to the fact most AC motors do not incorporate brushes. This signifies that servicing and elements substitute wants for AC motors are inclined to be significantly lowered, with most users usually anticipating a more time average lifespan. Unlike DC motors, the output pace of a lot of varieties of AC motors is usually established by inverter manage – once again, we will briefly outline a selection of prospective versions on the basic AC motor product.

China Best Sales Low Speed Electric 12/24/48V DC Gear Motor for Welding Machine Double Shaft     near me shop

China factory Electronic monitor low speed 6-24V DC planetary gear motor near me factory

Product Description

Electronic keep an eye on low speed 6-24V dc planetary gear motor

Principal Attributes
one.OEM&solODM 28mm gearbox plus 380&385 permanent CZPT DC motor & 28mm brushless motor
2.Small dimensions dc equipment motor with lower speed and massive torque
3.28mm gear motor offer 2.0Nm torque and more dependable
4.Suitable to modest diameter, lower sound and huge torque application
5.DC Gear motor can match enchoder, 11ppr 
6.Reduction ratio:4,fourteen,19,27,51,71,one hundred,one hundred thirty five,189,264,369,516,720

                                       Model:Motor GMP28-385SP
 
TRS-385SP-0640
Rated voltage:6V DC Rated speed:3250r&solmin Output electricity:1.6W
No-load velocity:4000r&solmin Rated torque:45g.cm Stall torque:250g&solcm
No-load current:200mA Rated current600mA Stall recent:2.5A
 
 
TRS-385SP-1265
Rated voltage:12V DC Rated speed:5200r&solmin Output electricity:3.2W
No-load pace:6500r&solmin Rated torque:60g.cm Stall torque:310g&solcm
No-load current:150mA Rated recent:500mA Stall present:2.0A
 
 
TRS-385SP-2454
Rated voltage:24V DC Rated pace:4000r&solmin Output electrical power:2.5W
No-load velocity:5400r&solmin Rated torque:60g.cm Stall torque:240g&solcm
No-load existing:100mA Rated current:200mA Stall current:.7A

 
Gear motor technical information : GMP28-385SP-0640-XXX

Reduction ratio four 19 27 51 one hundred 189 264 369 516 720
Duration mm 28.5 36 36 forty three 43 50 50 fifty fifty fifty
No-load pace rpm 900 a hundred ninety 140 seventy five 38 20 15 eleven eight 5
Rated pace rpm 810 a hundred and seventy one hundred twenty 64 32 seventeen twelve nine six four
Rated torque kg.cm .fourteen .6 .nine one.four two.7 4.7 six 8 11 thirteen
Max.momentary tolerance torque kg.cm .eight three.3 four.seven seven.six fifteen 26 30 thirty 30 thirty

Equipment motor technical knowledge : GMP28-385SP-1265-XXX

Reduction ratio four 19 27 51 a hundred 189 264 369 516 720
Length mm 28.five 36 36 43 forty three 50 fifty 50 fifty fifty
No-load velocity rpm 1500 330 230 one hundred twenty 63 34 23 16 twelve eight
Rated speed rpm 1300 270 one hundred ninety a hundred 52 27 twenty 14 10 seven
Rated torque kg.cm .19 .eight one.1 one.eight 3.six six eight 11 fifteen seventeen
Max.momentary tolerance torque kg.cm one. four.1 5.8 9.five 19 30 thirty thirty 30 thirty

Equipment motor specialized data : GMP28-385SP-2454-XXX

Reduction ratio four 19 27 fifty one 100 189 264 369 516 720
Size mm 28.5 36 36 43 forty three 50 50 50 fifty fifty
No-load speed rpm 1250 270 190 100 50 29 20 15 ten eight
Rated speed rpm a thousand 210 a hundred and fifty 78 40 21 fifteen eleven 8 6
Rated torque kg.cm .19 .eight one.1 one.eight three.six 6 8 eleven 15 17
Max.momentary tolerance torque kg.cm .eight three.two four.5 seven.3 14 25 30 30 thirty thirty

Item Application

Other Programs:
Business Devices: ATM, Copiers and Scanners, Forex Handling, Point of Sale, Printers, Vending Devices.
Meals and Beverage: Beverage Dispensing, Hand Blenders, Blenders, Mixers, Espresso Devices, Foods Processors, Juicers, Fryers, Ice Makers, Soy Bean Milk Makers.
Home Entertainment and Gaming: Gaming Equipment, Online video Games, Optical Disk Drives, RC and Power Toys.
Property Systems: Residence Air flow, Air Purifiers and Dehumidifiers, Assortment Hoods, Washers and Dryers, Fridges, Dishwashers, Floor Care, Whirlpool and Spa, Showers, Intelligent Metering, Espresso Machines.
Garden and Backyard: Garden Mowers, Snow Blowers, Trimmers, Leaf Blowers.
Private Care: Hair Slicing, Hair Care, Massagers.
Power Resources: Drills and Motorists, Sanders, Grinders, Polishers, Saws.
Digicam and Optical: Online video, Cameras, Projectors.

Packing & Delivery
Packaging: single carton packing, a hundred items for every box.
Shipping and delivery time:
DHL: 3-5 working days &semi
UPS: 5-7 doing work days&semi
TNT: 5-7 working days&semi
FedEx: 7-9 working days&semi
EMS: twelve-15 functioning days&semi
By Sea: Depends on which country

Our Company 
TT Motor &lparHK) Industrial Co., Ltd has been specializing in CZPT motors, equipment motors and their respective elements given that 2000.
Our goods are broadly employed in entertainment techniques, vehicles, home and industrial appliances and resources and a lot of other individuals. Our merchandise are trustworthy and lengthy-lasting, and backed by a long time of encounter. We export 98&percnt of our output worldwide. 
By leveraging our hard-gained track record for honesty, dependability and good quality, TT Motor aims to carry on as a pioneer in the revenue abroad by in search of global associates. If your organization is an end-person of micro-motors, a distributor or an agent, you should make contact with us. We seem ahead to getting in a position to operate with each other with you in the around potential.

FAQ
Q: How to get&quest
A: send out us inquiry &rightarrow receive our quotation &rightarrow negotiate information &rightarrow confirm the sample &rightarrow sign agreement&soldeposit &rightarrow mass production &rightarrow cargo all set &rightarrow balance&soldelivery &rightarrow further cooperation.
Q: How about Sample purchase&quest
A: Sample is offered for you. make sure you speak to us for specifics. Contact us
Q: Which delivery way is avaliable&quest
A: DHL, UPS, FedEx, TNT, EMS, China Post,Sea are accessible.The other shipping ways are also accessible, you should speak to us if you need to have ship by the other transport way. 
Q: How extended is the deliver&quest
A: Devliver time is dependent on the amount you get. typically it normally takes 15-twenty five operating times.
Q: My deal has lacking products. What can I do&quest
A: Remember to contact our support group and we will verify your order with the deal contents.We apologize for any inconveniences. 
Q: How to verify the payment&quest
A: We acknowledge payment by T&solT, PayPal, the other payment methods also could be acknowledged,You should contact us just before you pay by the other payment methods. Also 30-50&percnt deposit is offered, the harmony cash should be compensated before transport.

An AC motor is a frequent sort of electric powered motor that is pushed by alternating recent. As the most effective practical motors for each day industrial applications (as properly as hobbyist assignments, home objects, and all other expert equipment and client items), AC motors provide a reasonably productive strategy of making mechanical strength from a straightforward electrical enter signal.
AC motors vary from a lot of other varieties of motors, particularly some of the a lot more common DC (immediate current) motors, by numerous essential requirements. The most simple of these is the truth that an AC motor relies entirely on the alternating recent all around its circuit to make efficient mechanical power. We will go over this distinctive procedure in a lot more depth in the pursuing sections of this manual.

China factory Electronic monitor low speed 6-24V DC planetary equipment motor     around me factory

China factory Low Rpm High Power Small AC Gear DC Gear Induction Motor Electric Car Motor Electrical Motor with Speed Controller 2 Phase 3 Phase with Good quality

Product Description

    Standard Specs
    Stage Precision   ±5%(Complete phase,No load)
    Temperature Rise   80ºCMax
    Surroundings Temperature   -10ºC – +50ºC
    Insulation Resistance   100MΩmin.500VDC
    Face up to Voltage   500VDC for 1 minute
    Radial Runout   .06Max.(450g-load)
    Axial Runout   .08Max.(450g-load)

 

Complex Specifications
Design Stage Stage
Angle
(°)
Keeping
Torque
N.M
Rated
Present
(A)
Stage
Inductance
mH
Phase Inductance
Ohm
57A09 2 one.eight .nine two.eight one.2 .8
57A1 two 1.eight 1.3 two.eight two.one 1.
57A2 2 1.eight 2.2 4. one.8 .8
Model Phase Amount
of Prospects
Rotor inertia
(g.cm²)
Shaft Diameter mm Fat

kg

Physique Duration
mm
57A09 2 4 260 six.35 .six fifty five
57A1 2 4 460 6.35 one. seventy six
57A2 2 4 460 eight one.one 80

The earlier mentioned are consultant items, spinoff items can be made according to customer demands.

 

Polyphase motors can be either two-period or 3-section motors. They work like one-stage induction motors, but both solitary-period and polyphase motors run on a rotating magnetic discipline. Their rotating magnetic fields are produced by two- or a few-period currents passing through two or far more sets of coils. The rotating magnetic discipline makes torque. Polyphase motors are employed in purposes that demand high electrical power, these kinds of as the electricity generate of compressors, hydraulic pumps, air conditioning compressors, and irrigation pumps.
The rotor of a reluctance motor is made up of a sound cast steel portion with a convex toothed rack. Their starting process is related to an induction motor, but it operates like a synchronous motor. Typically, their rotors have less poles than stators, which minimizes torque ripple and prevents excellent pole alignment, as no torque is developed in that place. Reluctance motors assortment in energy scores from a handful of watts to about 22 kilowatts.

China factory Low Rpm High Power Small AC Gear DC Gear Induction Motor Electric Car Motor Electrical Motor with Speed Controller 2 Stage 3 Period     with Good high quality